Lexus NX: Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)
DESCRIPTION
If a door glass or a power window regulator motor assembly does not operate smoothly, the jam protection function may be triggered automatically, resulting in the auto up operation being unable to fully close the window.
CAUTION / NOTICE / HINT
NOTICE:
-
If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.
Click here
.gif)
-
If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.
Click here
HINT:
This symptom may occur for any of the windows.
PROCEDURE
| 1. | PERFORM INITIALIZATION (APPLICABLE LOCATION) |
(a) Initialize the power window regulator motor assembly (applicable location).
Click here
|
.gif)
| 2. | CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION [APPLICABLE LOCATION]) |
(a) Check that each power window moves when the auto up and down function of the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly (for rear LH or RH door) is operated.
Click here
OK:
Auto up and down function is normal (applicable location).
| OK | .gif) | END (PROBLEM DUE TO INITIALIZATION FAILURE) |
|
| 3. | CHECK WINDOW GLASS SLIDING MOVEMENT (APPLICABLE LOCATION) |
(a) Remove the door window regulator.
-
for Front Door:
Click here
-
for Rear Door:
Click here
(b) Install the window glass to the door glass run.
-
for Front Door:
Click here
-
for Rear Door:
Click here
(c) Check if the door window regulator operates smoothly.
(d) Check that the window glass slides smoothly when sliding it up by hand.
CAUTION:
Perform initialization again.
HINT:
Ensure the following:- The window glass fits with the glass run without improper contact or deformation.
- Foreign matter is not caught in the glass run.
- The glass run is not misaligned.
- The belt moulding or inner weatherstrip is not caught.
- The glass is not tilted and does not catch.
OK:
Door window glass slides smoothly.
| Result | Proceed to |
|---|---|
| OK (Driver door power window) | A |
| OK (Front passenger door power window) | B |
| OK (Rear LH door power window) | C |
| OK (Rear RH door power window) | D |
| NG | E |
| A | | REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
| B | | REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH |
| C | | REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
| D | | REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH |
| E | | FIT WINDOW GLASS CORRECTLY (REMOVE FOREIGN MATTER CAUSING IMPROPER FIT OR REPLACE PARTS) |
READ NEXT:
Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)
DESCRIPTION If a door glass or a power window regulator motor assembly does not operate smoothly, the catch protection function may be triggered automatically, resulting in the auto down operation bei
Jam Protection Function does not Operate
DESCRIPTION This symptom may occur for any of the windows. The jam protection function operates within a specified range during the manual up or auto up operation. CAUTION / NOTICE / HINT NOTICE:
I
Power Window Master Switch
ComponentsCOMPONENTS ILLUSTRATION *1 MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY *2 POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL *3 FRONT DOOR ARMREST
SEE MORE:
USB Audio System Recognition/Play Error
DESCRIPTION When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio receiver assembly. This diagnosis procedure is for when a device is not recognized, or fil
Short to +B in Outer Mirror Indicator(Slave) (C1AB1)
DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects a +B short in the outer rear view mirror indicator RH. DTC No. Detection Item DTC Detection Condition Trouble Area Note C1AB1 Short to +B in Outer Mirror Indicator(Slave) Both of the following conditions
