Lexus NX: Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
DESCRIPTION
This DTC is stored when items controlled by the certification ECU cannot be customized via the navigation system vehicle customization screen.
HINT:
The certification ECU controls the smart access system with push-button start (for Entry Function) related items that are customizable via the multi-display assembly screen.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15F7 | Certification ECU Vehicle Information Reading/Writing Process Malfunction | Certification ECU vehicle setting processing error. |
|
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing the radio receiver assembly, always replace it with a new one.
If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio receiver assembly may not operate normally.
-
Before replacing the certification ECU (smart key ECU assembly), refer to smart access system with push-button start (for Entry Function) Precaution.
Click here
Click here
.gif)
HINT:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
PROCEDURE
| 1. | CHECK CAN COMMUNICATION SYSTEM |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
OK:
CAN communication DTCs are not output.
| NG | .gif) | GO TO CAN COMMUNICATION SYSTEM |
|
.gif)
| 2. | CHECK SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function) |
(a) Check if the smart access system with push-button start (for Entry Function) is malfunctioning.
Click here
HINT:
Customization may not be possible depending on the malfunction in the smart access system with push-button start (for Entry Function).
OK:
No malfunctions are present in the smart access system with push-button start (for Entry Function).
| NG | | GO TO SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function) |
|
| 3. | CHECK CUSTOMIZE ITEMS |
(a) Display the "Vehicle Customization" screen.
(b) Make a note of the customizable items for each certification ECU related system.
HINT:
These items shown as customizable via the navigation system vehicle customization screen can also be changed manually. In a following step, a manual procedure will be used.
(1) Check the customize parameters list for the smart access system with push-button start (for Entry Function) related items that can be customized via the multi-display assembly screen.
Click here
(c) Manually change and confirm that it was possible to successfully change the settings of the customize parameters for each system that are available for customization via the multi-display assembly screen.
OK:
The items available for customization via the multi-display assembly screen can be customized successfully using the manual procedure.
| OK | | REPLACE RADIO RECEIVER ASSEMBLY |
| NG | | REPLACE CERTIFICATION ECU |
READ NEXT:
D-Seat ECU Vehicle Information Reading/Writing Process Malfunction (B15F8)
DESCRIPTION This DTC is stored when items controlled by the position control ECU assembly (driver seat) cannot be customized via the navigation system vehicle customization screen. HINT: The position
XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION These DTCs are stored when a malfunction occurs in the roof antenna assembly which is connected to the radio receiver assembly. DTC No. Detection Item DTC Detection Condition Trou
Camera ECU Malfunction (C1610)
DESCRIPTION This DTC is stored when a malfunction occurs in the park assist/monitoring section. DTC No. Detection Item DTC Detection Condition Trouble Area C1610 Camera ECU Malfunction
SEE MORE:
Cargo and luggage
Take notice of the following information
about storage precautions,
cargo capacity and load.
WARNING
■Things that must not be carried in the
luggage compartment
The following things may cause a fire if
loaded in the luggage compartment:
Receptacles containing gasoline
Aerosol cans
Removal
REMOVAL PROCEDURE 1. REMOVE SYMBOL EMBLEM HINT: When removing the symbol emblem, heat the back door outside garnish sub-assembly and symbol emblem using a heat light. Standard: Item Temperature Back Door Outside Garnish Sub-assembly 40 to 60°C (104 to 140°F) Symbol Emblem 20 to 3
