Lexus NX: Back Camera Power Supply Failure (C1621)
DESCRIPTION
This DTC is stored if the parking assist ECU determines that the input/output signal communication with the rear television camera assembly is abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1621 | Back Camera Power Supply Failure | Rear television camera assembly power supply malfunction |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click here
.gif)
-
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click here
PROCEDURE
| 1. | CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY) |
(a) Disconnect the P45 parking assist ECU connector.
(b) Disconnect the Y25 rear television camera assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P45-33 (CB+) - Y25-6 (CB+) | Always | Below 1 Ω |
| P45-32 (CGND) - Y25-5 (CGND) | Always | Below 1 Ω |
| P45-33 (CB+) or Y25-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| P45-32 (CGND) or Y25-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| NG | .gif) | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
.gif)
| 2. | CHECK PARKING ASSIST ECU (CB+, CGND) |
| (a) Disconnect the rear television camera assembly. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P45-32 (CGND) - Body ground | Always | Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| P45-33 (CB+) - P45-32 (CGND) | Power switch on (IG) | 5.5 to 7.05 V |
| P45-33 (CB+) - P45-32 (CGND) | Power switch off | Below 1 V |
| OK | | REPLACE REAR TELEVISION CAMERA ASSEMBLY |
| NG | | REPLACE PARKING ASSIST ECU |
READ NEXT:
Open or Short Circuit in Back Camera Signal (C1622)
DESCRIPTION This DTC is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly ar
Open or Short in Steering Angle Sensor +B (C1625)
DESCRIPTION This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem. DTC No. Detection Item DT
Steering Angle Sensor Failure (C1626)
DESCRIPTION This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates an internal malfunction. DTC No. Detection Item DTC Dete
SEE MORE:
Lost Communication with Hybrid Vehicle Control System (U0293)
MONITOR DESCRIPTION The ECM communicates with the hybrid vehicle control ECU. When the ECM does not receive data from the hybrid vehicle control ECU, the ECM illuminates the MIL and stores a DTC. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory U0293 Lost Com
Fuel Receiver Gauge Display Malfunction
DESCRIPTION OPERATION The combination meter assembly uses the fuel injection volume signal from the ECM, fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. Each gauge assembly has a variable resistor whose resistance changes according to the amount of fuel r
