Lexus NX: Components
COMPONENTS
ILLUSTRATION
| *1 | DECK FLOOR BOX LH | *2 | NO. 3 DECK BOARD SUB-ASSEMBLY |
| *3 | REAR DECK FLOOR BOX | *4 | NEGATIVE AUXILIARY BATTERY TERMINAL |
.png) | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for Driver Side | *B | for Front Passenger Side |
| *C | for Driver Side with Memory | - | - |
| *1 | FRONT DOOR ARMREST SET BRACKET LH | *2 | FRONT DOOR INNER GLASS WEATHERSTRIP LH |
| *3 | FRONT DOOR INSIDE HANDLE BEZEL PLUG LH | *4 | FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH |
| *5 | FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH | *6 | FRONT DOOR TRIM COVER LH |
| *7 | FRONT SEAT SLIDE SWITCH BEZEL | *8 | POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL |
| *9 | POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL | *10 | SEAT MEMORY SWITCH |
ILLUSTRATION
| *A | for 8 Speakers | *B | for 10 Speakers |
| *C | for 14 Speakers | - | - |
| *1 | DOOR SIDE AIR BAG SENSOR LH | *2 | FRONT DOOR GLASS RUN LH |
| *3 | FRONT DOOR SERVICE HOLE COVER LH | *4 | FRONT NO. 1 SPEAKER ASSEMBLY |
| *5 | OUTER MIRROR CONTROL ECU ASSEMBLY | *6 | OUTER MIRROR INSTALL HOLE COVER LH |
| *7 | OUTER REAR VIEW MIRROR ASSEMBLY LH | *8 | HOLE COVER |
| *9 | BUTYL TAPE | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for Driver Side | *B | for Front Passenger Side |
| *1 | DOOR OUTSIDE HANDLE BUSH | *2 | FRONT DOOR FIX WINDOW GLASS LH |
| *3 | FRONT DOOR FIX WINDOW WEATHERSTRIP LH | *4 | FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH |
| *5 | FRONT DOOR FRONT OUTSIDE HANDLE PAD | *6 | FRONT DOOR GLASS SUB-ASSEMBLY LH |
| *7 | FRONT DOOR LOCK ASSEMBLY LH | *8 | FRONT DOOR LOCK CYLINDER ASSEMBLY LH |
| *9 | FRONT DOOR LOCK OPEN ROD LH | *10 | FRONT DOOR NO. 1 STIFFENER CUSHION |
| *11 | FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH | *12 | FRONT DOOR OUTSIDE HANDLE COVER RH |
| *13 | FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH | *14 | FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH |
| *15 | FRONT DOOR REAR OUTSIDE HANDLE PAD | *16 | FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
| *17 | HOLE COVER | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
.png) | MP grease | - | - |
ILLUSTRATION
| *1 | FRONT DOOR BELT MOULDING ASSEMBLY LH | *2 | FRONT DOOR CHECK ASSEMBLY LH |
| *3 | FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH | *4 | FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH |
| *5 | FRONT DOOR PANEL CUSHION | *6 | FRONT DOOR REAR WINDOW FRAME MOULDING LH |
| *7 | FRONT DOOR UPPER OUTSIDE MOULDING PAD | *8 | FRONT DOOR WEATHERSTRIP LH |
| *9 | NO. 1 BLACK OUT TAPE LH | *10 | NO. 2 BLACK OUT TAPE LH |
| *11 | NO. 3 BLACK OUT TAPE LH | *12 | UPPER DOOR FRAME GARNISH LH |
| *13 | HOLE PLUG | *14 | HOLE COVER |
| *15 | RIVET | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ★ | Precoated part |
| | MP grease | ● | Non-reusable part |
READ NEXT:
Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH side.
The procedure listed below is for the LH side.
PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precaut
Inspection
INSPECTION PROCEDURE 1. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH (a) Check that the LED illuminates. (1) Apply 6.0 V (4 dry cell batteries in series) to each terminal and check the illuminatio
Adjustment
ADJUSTMENT CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
Centering bolts are used to mount the door hinge to the v
SEE MORE:
XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION These DTCs are stored when a malfunction occurs in the roof antenna assembly which is connected to the radio receiver assembly. DTC No. Detection Item DTC Detection Condition Trouble Area B15FE XM Tuner Antenna Disconnected The roof antenna assembly is not connected.
Crankshaft Position Sensor
ComponentsCOMPONENTS ILLUSTRATION *1 CRANKSHAFT POSITION SENSOR - - N*m (kgf*cm, ft.*lbf) : Specified torque Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent ★ Precoated part - - RemovalREMOVAL PROCEDURE 1. REMOVE CRANKSHAFT POSITION SENSOR (a) Disc
