Lexus NX: Vehicle Exterior
Lexus NX Service Manual / Vehicle Exterior
- Acoustic Vehicle Alerting System
- Door / Hatch
- Back Door
- Back Door Closer Ecu
- Back Door Closer System
- Back Door Opener Switch
- Back Door Support
- Back Door Weatherstrip
- Front Door
- Front Door Opening Trim Weatherstrip
- Fuel Lid Opener Motor Assembly
- Fuel Lid Opener System
- Hood
- Hood Lock Control Cable Assembly
- Hood Support
- Kick Sensor
- Power Back Door Control Switch
- Power Back Door Drive Unit
- Power Back Door Main Switch
- Power Back Door System
- Power Back Door Touch Sensor
- Power Back Door Warning Buzzer
- Rear Door
- Rear Door Opening Trim Weatherstrip
- Relay
- Reserve Lock Switch
- Exterior Panels / Trim
- Back Door Outside Garnish
- Black Out Tape (for Front Door)
- Black Out Tape (for Rear Door)
- Front Bumper (except Sport Package)
- Front Bumper (for Sport Package)
- Front Door Belt Moulding
- Front Door Outside Moulding
- Front Door Window Frame Moulding
- Name Plate
- Radiator Grille (except Sport Package)
- Radiator Grille (for Sport Package)
- Rear Bumper
- Rear Door Belt Moulding
- Rear Door Outside Moulding
- Rear Door Window Frame Moulding
- Rear Spoiler
- Rear Wheel House Plate
- Roof Drip Side Finish Moulding
- Roof Rack
- Side Mudguard
- Wheel Opening Moulding(for Front)
- Wheel Opening Moulding(for Rear)
- Horn
- Lighting (ext)
- Afs (adaptive Front-lighting System)
- Automatic Headlight Beam Level Control System (for Triple Beam Headlight)
- Automatic High Beam Main Switch
- Automatic High Beam System
- Automatic Light Control Sensor
- Clearance Light Assembly (for Bulb Type Turn Signal Light)
- Clearance Light Assembly (for Led Type Turn Signal Light)
- Fog Light Assembly (except Sport Package)
- Fog Light Assembly (for Sport Package)
- Front Side Marker Light Bulb(for Single Beam Headlight)
- Front Turn Signal Light Bulb(for Bulb Type Turn Signal Light)
- Hazard Warning Switch
- Headlight Assembly (for Triple Beam Headlight)
- Headlight Assembly(for Single Beam Headlight)
- Headlight Dimmer Switch
- Headlight Ecu
- Height Control Sensor
- High Mounted Stop Light Assembly
- License Plate Light Assembly
- Lighting System (for Single Beam Headlight)
- Lighting System (for Triple Beam Headlight)
- Rear Combination Light Assembly
- Rear Light Assembly
- Side Turn Signal Light Assembly
- Stop Light Control Relay
- Stop Light Switch
- Mirror (ext)
- Outer Mirror Control Ecu
- Outer Mirror Switch
- Outer Rear View Mirror
- Outer Rear View Mirror Glass
- Power Mirror Control System (w/ Memory)
- Power Mirror Control System (w/o Memory)
- Relay
- Sliding Roof / Convertible
- Window / Glass
- Back Door Glass
- Front Passenger Side Power Window Switch
- Power Window Control System
- Power Window Master Switch
- Power Window Regulator Motor (for Front Side)
- Power Window Regulator Motor (for Rear Side)
- Quarter Window Glass
- Rear Power Window Switch
- Relay
- Window Defogger System
- Windshield Deicer System
- Windshield Glass
- Wiper / Washer
- Front Wiper Motor
- Front Wiper Rubber
- Headlight Cleaner Actuator
- Headlight Cleaner Actuator Cover
- Headlight Cleaner Control Relay (for Single Beam Headlight)
- Headlight Cleaner Control Relay(for Triple Beam Headlight)
- Headlight Cleaner Motor
- Rain Sensor
- Rear Wiper Motor
- Rear Wiper Rubber
- Washer Level Warning Switch
- Washer Motor
- Washer Nozzle
- Washer Nozzle(for Rear Side)
- Wiper And Washer System
- Wiper Ecu
- Wiper Switch
READ NEXT:
Precaution
PRECAUTION PRECAUTIONS FOR VEHICLE PROXIMITY NOTIFICATION SYSTEM (a) In the following cases, the volume or tone of the sound might change: (1) If the vehicle is parked in a very hot or cold environmen
SEE MORE:
Reassembly
REASSEMBLY CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH side.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart.
Click here PROCEDURE 1. REPAIR INSTRUCTION Click here 2. INSTALL NO. 1 BLACK
Power Source Circuit
DESCRIPTION This circuit provides power to operate the blind spot monitor sensor. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following inspection procedure. PROCEDURE 1. CHECK HARNESS AND CONNECTOR (BLIND SPOT MON
© 2016-2026 Copyright www.lexunx.com
