Lexus NX: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE SLIDING ROOF SYSTEM
HINT:
The following items can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make notes of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(a) Customizing with the Techstream
(1) Connect the Techstream to the DLC3.
(2) Turn the power switch on (IG).
(3) Turn the Techstream on.
(4) Enter the following menus: Customize Setting / Power Window.
(5) Select the setting by referring to the table below.
Power Window| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Door Key P/W Up | This function is used to close the power windows and sliding roof by operating the mechanical key. | OFF | 0:OFF,1:ON | Main body ECU (multiplex network body ECU) |
| Door Key P/W Down | This function is used to open the power windows and sliding roof by operating the mechanical key. | OFF | 0:OFF,1:ON | Main body ECU (multiplex network body ECU) |
| P/W Up W/ Transmit | This function is used to close the power windows and sliding roof using the wireless key transmitter. | OFF | 0:OFF,1:ON | Main body ECU (multiplex network body ECU) |
| P/W Down W/ Transmit | This function is used to open the power windows and sliding roof using the wireless key transmitter. | OFF | 0:OFF,1:ON | Main body ECU (multiplex network body ECU) |
(6) Enter the following menus: Customize Setting / Slide Roof.
(7) Select the setting by referring to the table below.
Slide Roof| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Front SW Auto Operation | This function is used to enable or disable auto operation. | ON | 0:OFF,1:ON | Sliding roof drive gear sub-assembly (sliding roof ECU) |
(8) Enter the following menus: Customize Setting / Security.
(9) Select the setting by referring to the table below.
Security| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Slide Roof Open Warning | This function is used to enable or disable the sliding roof open warning. | ON | 0:OFF,1:ON | Main body ECU (multiplex network body ECU) |
READ NEXT:
Initialization
INITIALIZATION INITIALIZE SLIDING ROOF SYSTEM NOTICE:
When the roof glass is adjusted or removed/installed, or the sliding roof drive gear sub-assembly is replaced, the glass position cannot be det
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of
Terminals Of Ecu
TERMINALS OF ECU CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (a) Disconnect the T9 sliding roof ECU (sliding roof drive gear sub-assembly) connector. (b) Measure the resistance and
SEE MORE:
Heated Oxygen Sensor
ComponentsCOMPONENTS ILLUSTRATION *1 FRONT EXHAUST PIPE SUB-ASSEMBLY *2 HEATED OXYGEN SENSOR *3 COMPRESSION SPRING *4 GASKET N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST ● Non-reusable part - - RemovalREMOVAL PROCEDURE 1. REMOVE FRONT EXH
Installation
INSTALLATION PROCEDURE 1. INSTALL BRAKE PEDAL PAD (a) Install the brake pedal pad to the brake pedal support assembly. 2. INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY Click here 3. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY (a) Install the brake pedal support assembly with the 4 nuts. Torque: 12.7 N·m {
