Lexus NX: Main Switch Circuit
DESCRIPTION
The stereo component equalizer assembly detects vehicle sound switch signals.
The ASC system can be turned on and off by operating the vehicle sound switch.
WIRING DIAGRAM
.png)
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM |
(a) Using the Techstream, read the Data List.
Click here .gif)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Volume SW | Vehicle sound switch on/off status | OFF or ON | OFF: Vehicle sound switch off ON: Vehicle sound switch on | - |
| Volume Switch Voltage | The VSLI terminal voltage to the CPU of the stereo compartment equalizer assembly | Min.: 0 V Max.: 5 V | Changes according to vehicle sound switch volume setting | - |
| Tester Display |
|---|
| Volume SW |
| Volume Switch Voltage |
OK:
The display is as specified in the normal condition column.
| OK | .gif) | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
.gif)
| 2. | INSPECT VEHICLE SOUND SWITCH |
(a) Remove the vehicle sound switch.
Click here
(b) Inspect the vehicle sound switch.
Click here
| NG | | REPLACE VEHICLE SOUND SWITCH |
|
| 3. | CHECK HARNESS AND CONNECTOR (VEHICLE SOUND SWITCH - BATTERY) |
| (a) Disconnect the vehicle sound switch connector. |
|
.png)
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I114-8 (NVS) - Body ground | Power switch on (IG) | 11 to 14 V |
| I114-8 (NVS) - Body ground | Power switch off | Below 1 V |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 4. | CHECK HARNESS AND CONNECTOR (VEHICLE SOUND SWITCH - STEREO COMPONENT EQUALIZER ASSEMBLY) |
(a) Disconnect the I114 vehicle sound switch connector.
(b) Disconnect the I117 stereo component equalizer assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I114-3 (NVI) - I117-5 (VLSW) | Always | Below 1 Ω |
| I114-6 (NVM) - I117-14 (VSLI) | Always | Below 1 Ω |
| I114-3 (NVI) or I117-5 (VLSW) - Body ground | Always | 10 kΩ or higher |
| I114-6 (NVM) or I117-14 (VSLI) - Body ground | Always | 10 kΩ or higher |
| OK | | REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
Power Source Circuit
DESCRIPTION This circuit is the power source circuit for the stereo component equalizer assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL NOTICE: After the power switch is turned off, the radio receiver assembly records various types of memory and set
SEE MORE:
Unable to Unlock Steering Wheel (Hybrid Control System cannot Start)
DESCRIPTION The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering. The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the power switch is turned on (IG
Back Door Courtesy Switch Circuit
DESCRIPTION The main body ECU (multiplex network body ECU) receives a back door open or closed signal from the back door courtesy light switch. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE:
Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
