Lexus NX: NTSC Disconnected (from Park Assist/Monitoring ECU) (B1535,C1622)
DESCRIPTION
This DTC is stored if the radio receiver assembly judges that the signals or signal lines between the television camera assembly and the multi-display assembly are not normal as a result of its self check.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1535 | NTSC Disconnected (from Park Assist/Monitoring ECU) | Open or short in the television camera assembly signal circuit |
|
| C1622 | Back Camera Disconnected | Open or short in the television camera assembly signal circuit |
|
WIRING DIAGRAM
.png)
CAUTION / NOTICE / HINT
NOTICE:
-
If the cable was disconnected from and reconnected to the negative (-) auxiliary battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".
Click here
.gif)
-
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Click here
-
When replacing the radio receiver assembly, always replace it with a new one.
If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio receiver assembly may not operate normally.
HINT:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
PROCEDURE
| 1. | CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - MULTI-DISPLAY ASSEMBLY) |
(a) Disconnect the Y25 television camera assembly connector.
(b) Disconnect the I42 multi-display assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y25-6 (CB+) - I42-10 (CA+) | Always | Below 1 Ω |
| Y25-3 (CV+) - I42-8 (V+) | Always | Below 1 Ω |
| Y25-2 (CV-) - I42-9 (V-) | Always | Below 1 Ω |
| Y25-5 (CGND) - I42-21 (CGND) | Always | Below 1 Ω |
| Y25-6 (CB+) or I42-10 (CA+) - Body ground | Always | 10 kΩ or higher |
| Y25-3 (CV+) or I42-8 (V+) - Body ground | Always | 10 kΩ or higher |
| Y25-2 (CV-) or I42-9 (V-) - Body ground | Always | 10 kΩ or higher |
| Y25-5 (CGND) or I42-21 (CGND) - Body ground | Always | 10 kΩ or higher |
| NG | .gif) | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
.gif)
| 2. | CHECK MULTI-DISPLAY ASSEMBLY (CA+, CGND) |
| (a) Remove the multi-display assembly with the connector still connected. Click here |
|
.png)
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I42-10 (CA+) - I42-21 (CGND) | Power switch on (ACC) | 5.5 to 7.05 V |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I42-21 (CGND) - Body ground | Always | Below 1 Ω |
| NG | | REPLACE MULTI-DISPLAY ASSEMBLY |
|
| 3. | CHECK TELEVISION CAMERA ASSEMBLY |
.png)
| *a | Component with harness connected | *b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
(a) Remove the multi-display assembly with the connector still connected.
Click here
(b) Check the waveform of the television camera assembly using an oscilloscope.
| Item | Content |
| Measurement terminal | I42-8 (V+) - I42-9 (V-) |
| Measurement setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Power switch on (READY), shift position in R, camera lens is not covered, displaying an image. Waveform 2: Power switch on (READY), shift position in R, camera lens is covered, blacking out the screen. |
HINT:
- The video waveform changes according to the image sent by the television camera assembly.
- The video waveform is constantly output when the power switch is on (ACC).
OK:
Waveform is as shown in the illustration.
| NG | | REPLACE TELEVISION CAMERA ASSEMBLY |
|
| 4. | CHECK MULTI-DISPLAY ASSEMBLY |
(a) Replace the multi-display assembly with a new or known good one.
Click here
(b) Clear the DTCs.
Click here
(c) Check for DTCs and check that no DTCs are output.
Click here
OK:
No DTCs are output.
| OK | | END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE) |
| NG | | REPLACE RADIO RECEIVER ASSEMBLY |
READ NEXT:
GVIF Disconnected (from Extension Module to H/U) (B153A)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B153A GVIF Disconnected (from Extension Module to H/U) GVIF disconnected (from navigation ECU to radio receiver
Extension Module Disconnected 2 (B1543)
DESCRIPTION If the radio receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the power switch is turned on (ACC) and the radio receiver assembly confirms
HD Radio Tuner Malfunction (B1551,B15A0,B15B3,B15B5,B15B7,B15BA,B15F9)
DESCRIPTION These DTCs are stored when a malfunction occurs in the radio receiver assembly DTC No. Detection Item DTC Detection Condition Trouble Area B1551 HD Radio Tuner Malfunction
SEE MORE:
Freeze Frame Data
FREEZE FRAME DATA FREEZE FRAME DATA/INFORMATION (a) Using the Techstream, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output. (b) The freeze frame data that is recorded when a DTC is stored can be used to check the INF codes, but only for DTCs which can be st
Terminals Of Ecu
TERMINALS OF ECU CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) *1 Main Body ECU (Multiplex Network Body ECU) - - (a) Measure the voltage and check for pulses according to the value(s) in the table below. Terminal No. (Symbol) Wiring C
