Lexus NX: Operation Check

OPERATION CHECK

NOTICE WHEN CHECKING FOLLOWING

(a) Wireless door lock/unlock function:

This wireless door lock control function operates only when the following 3 conditions are met:

(1) The power switch is off.

(2) All doors are closed.

(3) The power door lock control system is operating properly.

HINT:

The unlock function operates even when a door is open.

(b) The size of the wireless door lock control operation area differs depending on the situation.

(1) The size of the operation area differs depending on the user and the way the electrical key transmitter sub-assembly is held.

(2) In certain areas, the wireless door lock control function will only operate partially for the operation area, which will be reduced due to the vehicle body shape and the influence of the surrounding environment.

(3) Since the electrical key transmitter sub-assembly uses weak radio waves, strong radio waves or electrical noise in the frequency used by the electrical key transmitter sub-assembly may reduce the size of the operation area and the wireless door lock control may not function.

(4) When the transmitter battery is weak, the size of the operation area is reduced and the wireless door lock control may not function.

HINT:

  • If the electrical key transmitter sub-assembly has been left in a place that is exposed to direct sunlight, such as on the instrument panel, it may cause the transmitter battery to be weakened or cause other related problems.
  • Do not place the electrical key transmitter sub-assembly near magnetic equipment, such as digital audio players, induction cookers, medical devices that generate low-frequency electromagnetic waves, etc.

CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

NOTICE:

The operation check below is based on the non-customized initial condition of the vehicle.

HINT:

  • The switches described in this text are the switches for transmitting signals. The switches are built into the electrical key transmitter sub-assembly.
  • All the functions listed below must be checked in comparison with the wireless door lock control operation area.

(a) Make sure that the vehicle is in an area that allows the wireless control function to operate.

(b) Check basic functions.

(1) Check whether the LED of the electrical key transmitter sub-assembly comes on 3 times when each switch is pressed and held for 5 seconds.

HINT:

If the transmitter LED illuminates once or twice but not a third time when the switch has been pressed and held for 5 seconds or more, it may have a weak transmitter battery.

(2) Check that all doors lock when the lock switch is pressed.

(3) Check that all doors unlock when the unlock switch is pressed*1.

(4) Check that the driver door unlocks when the unlock switch is pressed once, and all doors unlock when pressed twice within 5 seconds*2.

(5) Check that the back door opens and closes when the back door open switch is pressed and held for 0.8 seconds or more*3.

  • *1: Customize item "Unlock 2 Operation" or "Remote 2-press unlock" is set "OFF".
  • *2: Customize item "Unlock 2 Operation" or "Remote 2-press unlock" is set "ON".
  • *3: w/ Power Back Door System

(c) Check the chattering prevention function.

(1) Check that the corresponding operation occurs only once and is not repeated continuously while the switch is held. However, when the switch is operated repeatedly at 1-second intervals, check that the corresponding operation is carried out.

(d) Check the answer-back (hazard warning light) function.

(1) When the lock switch is pressed, check that the hazard warning lights flash once simultaneously with the locking operation of all doors.

(2) When the unlock switch is pressed, check that the hazard warning lights flash twice simultaneously with the unlocking operation of all doors*1.

(3) When the unlock switch is pressed, check that the hazard warning lights flash twice simultaneously with the unlocking operation of the driver door*2.

  • *1: Customize item "Unlock 2 Operation" or "Remote 2-press unlock" is set "OFF".
  • *2: Customize item "Unlock 2 Operation" or "Remote 2-press unlock" is set "ON".

(e) Check the answer-back (wireless door lock buzzer) function.

(1) When the lock switch is pressed, check that the buzzer sounds once simultaneously with the locking operation of all doors.

(2) When the unlock switch is pressed once, check that the buzzer sounds twice simultaneously with the unlocking operation of all doors*1.

(3) When the unlock switch is pressed once, check that the buzzer sounds twice simultaneously with the unlocking operation of the driver door*2.

(4) When the back door is opened and closed by wireless operation, the wireless door lock buzzer sounds*3.

  • *1: Customize item "Unlock 2 Operation" or "Remote 2-press unlock" is set "OFF".
  • *2: Customize item "Unlock 2 Operation" or "Remote 2-press unlock" is set "ON".
  • *3: w/ Power Back Door System

(f) Check the switch operation fail-safe function.

(1) Check that the doors cannot be locked/unlocked when operating a switch on an unregistered electrical key transmitter sub-assembly, but that the doors can be locked/unlocked when operating a switch on the registered electrical key transmitter sub-assembly.

(g) Check the automatic locking function.

(1) Check that the doors relock automatically as long as none of the doors have been opened or all doors have not been locked within approximately 60 seconds of all doors being unlocked by pressing the unlock switch.

(2) Check that the automatic locking function does not operate when any door has been opened within approximately 60 seconds of unlocking the doors by pressing the unlock switch.

(3) Check that the automatic locking function does not operate when all doors have been locked manually (such as using key linked operation, or by pressing the lock switch) within approximately 60 seconds of unlocking the doors by pressing the unlock switch.

(h) Check the door ajar warning function.

(1) Check that the wireless door lock buzzer sounds for approximately 5 seconds when the lock switch is pressed with any of the doors ajar or open.

(i) Check the repeat function.

(1) Check that all doors attempt to automatically lock once again 1 second after the lock switch has been pressed while the driver door control knob is being held in the unlock position.

(j) Check the door lock stop function that operates when a door is open/ajar.

(1) With a door open or ajar, check that the doors cannot be locked when the lock switch is operated.

HINT:

The doors can be unlocked even when a door is open or ajar.

(k) Check the power back door reservation lock function (w/ Power Back Door System).

(1) Check that the doors lock after the back door is closed when the electrical key transmitter lock switch is operated during the back door closing operation via the power back door function.

(l) Check the panic alarm control function.

Click here

(m) Check the illuminated entry function.

Click here

(n) Check the power window down function.

Click here

Click here

(o) Check the memory call function (w/ Memory).

Click here

READ NEXT:

 Customize Parameters

CUSTOMIZE PARAMETERS CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM HINT: The following items can be customized. NOTICE: When the customer requests a change in a function, first make sure that the fun

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE NOTICE: If the main body ECU (multiplex network body ECU) is replaced, refer to the Smart Access System with Push-button Start (for Entry Function). Click here HINT: Use t

 Terminals Of Ecu

TERMINALS OF ECU CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) *1 Main Body ECU (Multiplex Network Body ECU) - - (a) Remove the main body E

SEE MORE:

 Rear Wiper Rubber

ComponentsCOMPONENTS ILLUSTRATION *1 REAR WIPER BLADE *2 REAR WIPER RUBBER *3 REAR WIPER BACKING PLATE - - ReplacementREPLACEMENT PROCEDURE 1. REMOVE REAR WIPER BLADE (a) Move the rear wiper arm. (b) Move the rear wiper blade until a "click" sound can be heard and the cla

 Inspection

INSPECTION PROCEDURE 1. INSPECT FRONT SEAT INNER BELT ASSEMBLY LH (a) Measure the resistance according to the value(s) in the table below. *1 Connector A *2 Connector B *3 Connector C - - *a Component without harness connected (Front Seat Inner Belt Assembly LH) - -

© 2016-2024 Copyright www.lexunx.com