Lexus NX: Vehicle Interior
Lexus NX Service Manual / Vehicle Interior
- Door Lock
- Back Door Lock
- Door Control Receiver
- Door Control Switch
- Door Control Transmitter
- Front Door Lock
- Power Door Lock Control System
- Rear Door Lock
- Transmitter Battery
- Wireless Door Lock Buzzer
- Wireless Door Lock Control System
- Heating / Air Conditioning
- Air Conditioning Amplifier
- Air Conditioning Panel
- Air Conditioning Pressure Sensor
- Air Conditioning System
- Air Conditioning Unit
- Ambient Temperature Sensor
- Blower Unit
- Compressor
- Condenser
- Cooler Expansion Valve
- Front Blower Motor
- Front Evaporator Temperature Sensor
- Heater Water Pump
- Humidity Sensor
- Ptc Heater Assembly
- Refrigerant
- Refrigerant Line
- Relay
- Room Temperature Sensor
- Solar Sensor
- Interior Panels / Trim
- Combination Switch
- Front Console Box
- Front Floor Footrest
- Lower Instrument Panel
- Roof Headlining
- Tonneau Cover Assembly
- Upper Instrument Panel
- Lighting (int)
- Back Door Courtesy Switch
- Console Box Light
- Footwell Light
- Front Door Courtesy Switch
- Glove Box Light
- Lighting System
- Luggage Compartment Room Light
- Personal Light
- Rear Door Courtesy Switch
- Relay
- Room Light
- Vanity Light
- Vanity Light Bulb
- Meter / Gauge / Display
- Clock
- Clock System
- Combination Meter
- Headup Display
- Headup Display Switch
- Headup Display System
- Light Control Rheostat
- Meter / Gauge System
- Trip Switch
- Mirror (int)
- Power Outlets (int)
- Accessory Socket System
- Power Outlet Socket
- Power Point Socket (for Luggage Compartment)
- Power Point Socket(for Console Box)
- Relay
- Voltage Inverter
- Wireless Charger Assembly
- Wireless Charging System
- Pre-collision
- Seat
- Climate Control Seat System
- Front Power Seat Control System (w/ Memory)
- Front Power Seat Control System(w/o Memory)
- Front Seat Assembly
- Front Seat Cushion Heater
- Front Seatback Heater
- Lumbar Support Adjuster Assembly
- Lumbar Switch
- Power Seat Switch (for Front Seat)
- Power Seat Switch (for Rear Seat)
- Rear Power Seat Control System
- Rear Seat Assembly (for Power Seat)
- Rear Seat Cushion Heater(for Manual Seat)
- Rear Seat Cushion Heater(for Power Seat)
- Rear Seatback Heater(for Manual Seat)
- Rear Seatback Heater(for Power Seat)
- Seat Heater Control (for Front Seat)
- Seat Heater Control(for Rear Seat)
- Seat Heater Switch(for Rear Seat)
- Seat Heater System
- Seat Memory Switch
- Seat Belt
- Front Seat Inner Belt Assembly
- Front Seat Outer Belt Assembly
- Rear Center Seat Outer Belt Assembly
- Rear Seat Inner Belt Assembly
- Rear Seat Outer Belt Assembly
- Seat Belt Tension Reducer System
- Seat Belt Warning Light (for Rear Side)
- Seat Belt Warning System
- Tongue Plate Stopper
- Supplemental Restraint Systems
- Airbag System
- Center Airbag Sensor Assembly
- Curtain Shield Airbag Assembly
- Front Airbag Sensor
- Front Passenger Airbag Assembly
- Front Seat Side Airbag Assembly
- Knee Airbag Assembly
- Occupant Classification Ecu
- Occupant Classification System
- Rear Airbag Sensor
- Seat Position Sensor
- Side Airbag Sensor
- Spiral Cable
- Srs Seat Cushion Airbag Assembly
- Steering Pad
- Theft Deterrent / Keyless Entry
- Certification Ecu
- Electrical Key Oscillator (for Front Floor)
- Electrical Key Oscillator (for Luggage Compartment)
- Electrical Key Oscillator (for Outside Luggage Compartment)
- Electrical Key Oscillator(for Rear Floor)
- Engine Hood Courtesy Switch
- Id Code Box
- Immobiliser System
- Intrusion Sensor
- Security Horn Assembly
- Security Horn Assembly (for Built-in Battery Type)
- Smart Access System With Push-button Start (for Entry Function)
- Smart Access System With Push-button Start (for Start Function)
- Theft Deterrent System
READ NEXT:
Components
COMPONENTS ILLUSTRATION *A w/o Power Back Door *B w/ Power Back Door *1 BACK DOOR FINISH COVER LH *2 BACK DOOR FINISH COVER RH *3 BACK DOOR CENTER GARNISH *4 BACK DOOR LO
SEE MORE:
Reassembly
REASSEMBLY PROCEDURE 1. INSTALL NUT (a) Install the 2 nuts. 2. INSTALL SYMBOL EMBLEM Click here 3. INSTALL BACK DOOR OUTSIDE GARNISH PROTECTOR (a) Clean the back door outside garnish surface. (1) Remove the double-sided tape from the back door outside garnish sub-assembly. (2) Wipe off any tape
Inspection
INSPECTION PROCEDURE 1. INSPECT NAVIGATION ANTENNA ASSEMBLY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Antenna Tester Connection Condition Specified Condition Navigation antenna 1 - 2 Always 50 to 500 Ω LTE sub-ann
© 2016-2026 Copyright www.lexunx.com
