Lexus NX: ABS Warning Light does not Come ON
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.
CAUTION / NOTICE / HINT
NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
Click here .gif)
PROCEDURE
| 1. | CHECK CAN COMMUNICATION SYSTEM |
(a) Check if CAN communication system DTCs are output.
Click here
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
| B | .gif) | INSPECT CAN COMMUNICATION SYSTEM |
|
.gif)
| 2. | PERFORM ACTIVE TEST USING TECHSTREAM (ABS WARNING LIGHT) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Select the Active Test on the Techstream.
Click here
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON/OFF | Observe combination meter assembly |
(d) Select the Data List on the Techstream.
Click here
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ABS Warning Light | ABS warning light | ON or OFF | ON: Warning light on OFF: Warning light off | - |
| Active Test Display |
|---|
| ABS Warning Light |
| Data List Display |
|---|
| ABS Warning Light |
(e) Check the operating condition of the ABS warning light when operating it using the Techstream.
| Result | Proceed to |
|---|---|
| ABS warning light in the Data List does not change using the Active Test. | A |
| ABS warning light in the Data List turns ON/OFF using the Active Test. | B |
| A | | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
|
| 3. | INSPECT COMBINATION METER ASSEMBLY |
(a) Turn the power switch off.
(b) Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.
Click here
| Tester Display |
|---|
| Indicat. Lamp ABS |
(c) Check the combination meter assembly.
OK:
The ABS warning light turns on or off in accordance with the Techstream operation.
| OK | | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| NG | | INSPECT METER / GAUGE SYSTEM |
READ NEXT:
Brake Warning Light Remains ON
DESCRIPTION The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication. If any of the following is detected, the brake warn
Brake Warning Light does not Come ON
DESCRIPTION The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication. CAUTION / NOTICE / HINT NOTICE: When replacing the
Brake Control Warning Light Remains ON
DESCRIPTION The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication. If the skid control ECU stores a DTC, the brake war
SEE MORE:
Steering Wheel does not Heat Up When Heated Steering Wheel Switch is Pressed
DESCRIPTION Click here WIRING DIAGRAM Click here CAUTION / NOTICE / HINT HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
The steering wheel heater unit is built into the steering wheel assembly which cannot be disassembled. T
Input Shaft Oil Seal
ComponentsCOMPONENTS ILLUSTRATION *1 HYBRID VEHICLE TRANSAXLE ASSEMBLY *2 INPUT SHAFT TYPE T OIL SEAL ● Non-reusable part MP grease ATF WS - - ReplacementREPLACEMENT PROCEDURE 1. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY Click here 2. REMOVE INPUT SHAFT TYPE
