Lexus NX: Components
COMPONENTS
ILLUSTRATION
| *A | for RH Side | - | - |
| *1 | REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY | *2 | REAR SEAT CUSHION MOULDING RH |
| *3 | REAR SEAT CUSHION MOULDING RH | *4 | REAR SEAT HEADREST ASSEMBLY |
| *5 | REAR SEAT INNER WITH CENTER BELT ASSY RH | *6 | REAR SEATBACK BOARD CARPET ASSEMBLY RH |
| *7 | REAR SEATBACK COVER | *8 | SEPARATE TYPE REAR SEATBACK COVER WITH PAD |
.png) | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LH Side | - | - |
| *1 | CENTER ARMREST HINGE COVER LH | *2 | CENTER SEAT HINGE COVER LH |
| *3 | NO. 1 SEAT ARMREST ASSEMBLY | *4 | NO. 1 SEATBACK COVER |
| *5 | REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY | *6 | REAR SEAT ARMREST HOLE COVER |
| *7 | REAR SEAT CENTER ARMREST ASSEMBLY | *8 | REAR SEAT CENTER HEADREST ASSEMBLY |
| *9 | REAR SEAT CUSHION MOULDING LH | *10 | REAR SEAT CUSHION MOULDING LH |
| *11 | REAR SEAT HEADREST ASSEMBLY | *12 | REAR SEAT INNER BELT ASSEMBLY LH |
| *13 | REAR SEATBACK BOARD CARPET ASSEMBLY LH | *14 | REAR SEATBACK COVER |
| *15 | SEPARETE TYPE REAR SEATBACK COVER WITH PAD | *16 | REAR SEATBACK PROTECTOR SHAFT |
| | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for RH Side | *B | for LH Side |
| *1 | SEPARATE TYPE REAR SEATBACK COVER LH (REAR SEATBACK HEATER ASSEMBLY LH) | *2 | SEPARATE TYPE REAR SEATBACK COVER RH (REAR SEATBACK HEATER ASSEMBLY RH) |
| *3 | SEPARATE TYPE REAR SEATBACK PAD LH | *4 | SEPARATE TYPE REAR SEATBACK PAD RH |
| *5 | HOG RING | - | - |
| ● | Non-reusable part | - | - |
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. REMOVE REAR SEAT ASSEMBLY Click here 2. REMOVE REAR SEATBACK COVER Click
Inspection
INSPECTION PROCEDURE 1. INSPECT SEPARATE TYPE REAR SEATBACK COVER RH (REAR SEATBACK HEATER ASSEMBLY RH) (for RH Side) (a) Check the separate type rear seatback cover RH (rear seatback heater assemb
Installation
INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (REAR SEATBACK HEATER AS
SEE MORE:
On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to follow the correct removal and installation procedures of the front seat cushion airbag assembly RH. HINT:
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
PROCEDURE 1. INSPECT F
Rough Idling (P1605)
DESCRIPTION When the engine is idling stably under a low load, if the idle speed drops or becomes unstable, this DTC will be stored. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troublesho
