Lexus NX manuals

Lexus NX: Inspection

Lexus NX Service Manual / Vehicle Interior / Seat / Rear Seatback Heater(for Power Seat) / Inspection

INSPECTION

PROCEDURE

1. INSPECT SEPARATE TYPE REAR SEATBACK COVER RH (REAR SEATBACK HEATER ASSEMBLY RH) (for RH Side)

(a) Check the separate type rear seatback cover RH (rear seatback heater assembly RH).

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A-1 - B-1

Always (23°C)

Below 1 Ω

A-2 - A-4

3.62 to 4.42 Ω

A-2 - B-5

A-3 - B-3

Below 1 Ω

A-4 - B-5

A-5 - B-2

If the result is not as specified, replace the separate type rear seatback cover RH (rear seatback heater assembly RH).

*a

Connector A

*b

Connector B

*c

Component without harness connected

(Separate Type Rear Seatback Cover RH (Rear Seatback Heater Assembly RH))

2. INSPECT SEPARATE TYPE REAR SEATBACK COVER LH (REAR SEATBACK HEATER ASSEMBLY LH) (for LH Side)

(a) Check the separate type rear seatback cover LH (rear seatback heater assembly LH).

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A-1 - B-1

Always (23°C)

Below 1 Ω

A-2 - A-4

3.62 to 4.42 Ω

A-2 - B-5

A-3 - B-3

Below 1 Ω

A-4 - B-5

A-5 - B-2

If the result is not as specified, replace the separate type rear seatback cover LH (rear seatback heater assembly LH).

*a

Connector A

*b

Connector B

*c

Component without harness connected

(Separate Type Rear Seatback Cover LH (Rear Seatback Heater Assembly LH))

READ NEXT:

 Installation

INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (REAR SEATBACK HEATER AS

 Seat Heater Control (for Front Seat)

ComponentsCOMPONENTS ILLUSTRATION *A for L-Sport *B for F-Sport *1 SEAT HEATER CONTROL SUB-ASSEMBLY LH - - RemovalREMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective glov

 Seat Heater Control(for Rear Seat)

SEE MORE:

 Removal

REMOVAL PROCEDURE 1. FRONT WHEELS FACING STRAIGHT AHEAD 2. SECURE STEERING WHEEL Click here 3. REMOVE COLUMN HOLE COVER SILENCER SHEET Click here 4. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY Click here 5. REMOVE FRONT WHEELS Click here 6. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

 Crankshaft Position Sensor

ComponentsCOMPONENTS ILLUSTRATION *1 CRANKSHAFT POSITION SENSOR - - N*m (kgf*cm, ft.*lbf) : Specified torque Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent ★ Precoated part - - RemovalREMOVAL PROCEDURE 1. REMOVE CRANKSHAFT POSITION SENSOR (a) Disc

© 2016-2026 Copyright www.lexunx.com