Lexus NX: Components
COMPONENTS
ILLUSTRATION
| *1 | SERVICE PLUG GRIP | *2 | BATTERY SERVICE HOLE COVER |
| *3 | HYBRID BATTERY SERVICE PLUG COVER | - | - |
.png) | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/o Performance Damper | *B | w/ Performance Damper |
| *1 | AIR CLEANER CAP SUB-ASSEMBLY | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *5 | OUTER COWL TOP PANEL | *6 | RADIATOR RESERVE TANK ASSEMBLY |
| *7 | SUSPENSION TOWER DAMPER | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | NO. 1 ENGINE UNDER COVER ASSEMBLY | - | - |
ILLUSTRATION
| *1 | FRONT CROSSMEMBER SUB-ASSEMBLY | *2 | FRONT ENGINE MOUNTING INSULATOR |
| *3 | FRONT EXHAUST PIPE ASSEMBLY | *4 | NO. 2 TRANSMISSION CONTROL CABLE BRACKET |
| *5 | TRANSMISSION CONTROL CABLE ASSEMBLY | *6 | WIRE HARNESS |
| *7 | GASKET | *8 | COMPRESSION SPRING |
| *9 | CLIP | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY | *2 | ENGINE MOUNTING INSULATOR LH |
| *3 | HYBRID VEHICLE TRANSAXLE ASSEMBLY | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | .png) | Adhesive |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *A | for Type A | *B | for Type B |
| *1 | AUTOMATIC TRANSMISSION CASE COVER | *2 | ENGINE MOUNTING BRACKET LH |
| *3 | FRONT ENGINE MOUNTING BRACKET | *4 | HYBRID TRANSMISSION MASS DAMPER |
| *5 | NO. 1 TRANSMISSION CONTROL CABLE BRACKET | *6 | NO. 2 AUTOMATIC TRANSMISSION CASE COVER |
| *7 | NO. 3 AUTOMATIC TRANSMISSION CASE COVER | *8 | NO. 3 INVERTER COOLING HOSE |
| *9 | NO. 3 OIL COOLER TUBE CLAMP | *10 | OIL COOLER TUBE CLAMP |
| *11 | REAR ENGINE MOUNTING BRACKET | *12 | REAR ENGINE MOUNTING INSULATOR |
| *13 | SHIFT LEVER POSITION SENSOR | *14 | TRANSMISSION OIL COOLER BRACKET |
| *15 | CONTROL SHAFT LEVER | *16 | LOCK PLATE |
| *17 | WASHER | *18 | GASKET |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| | Adhesive | ★ | Precoated part |
ILLUSTRATION
| *1 | MOTOR CONNECTOR PROTECTOR | *2 | NO. 1 MOTOR WATER JACKET COVER ASSEMBLY |
| *3 | NO. 2 MOTOR WATER JACKET COVER ASSEMBLY | *4 | NO. 3 MOTOR WATER JACKET COVER ASSEMBLY |
| *5 | TRANSAXLE BREATHER PLUG | *6 | UNION |
| *7 | O-RING | *8 | DRAIN PLUG |
| *9 | FILLER PLUG | *10 | GASKET |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| | Adhesive | ★ | Precoated part |
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter
Installation
INSTALLATION PROCEDURE 1. INSTALL NO. 3 MOTOR WATER JACKET COVER ASSEMBLY Click here 2. INSTALL NO. 1 MOTOR WATER JACKET COVER ASSEMBLY Click here 3. INSTALL NO. 2 MOTOR WATER JACKET COVER ASSEMBL
Input Shaft Oil Seal
ComponentsCOMPONENTS ILLUSTRATION *1 HYBRID VEHICLE TRANSAXLE ASSEMBLY *2 INPUT SHAFT TYPE T OIL SEAL ● Non-reusable part MP grease ATF WS - - ReplacementREPLACE
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL AIR CONDITIONER PRESSURE SENSOR (a) Remove the vinyl tape from the liquid pipe sub-assembly and the connecting part of the air conditioner pressure sensor. (b) Apply sufficient compressor oil to the O-ring of a new air conditioner pressure sensor and the connecting
Steering Angle Sensor Unusual Bank Angle Detected (C1440)
DESCRIPTION If the skid control ECU (brake booster with master cylinder assembly) determines that the vehicle is being driven at a steep bank angle, the skid control ECU (brake booster with master cylinder assembly) stores DTC C1440 while VSC operation is temporarily disabled. This is not a malfunct
