Lexus NX: Fuel Sender Open Detected (B1500)
DESCRIPTION
This DTC is stored when the combination meter detects a fuel sender gauge malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1500 | Fuel Sender Open Detected | Both conditions are met:
|
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
Be careful of flames.
NOTICE:
When replacing the combination meter assembly, make sure to replace it with a new one.
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM (FUEL INPUT) |
(a) Using the Techstream, read the Data List.
Click here .gif)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input | Min.: 0, Max.: 127.5 | Current fuel level displayed | Unit: Liter |
| Tester Display |
|---|
| Fuel Input |
OK:
Fuel amount value displayed on the Techstream is almost the same as the needle indication.
| OK | .gif) | REPLACE COMBINATION METER ASSEMBLY |
|
.gif)
| 2. | INSPECT FUEL SENDER GAUGE ASSEMBLY |
(a) Remove the fuel sender gauge assembly.
Click here
(b) Inspect the fuel sender gauge assembly.
Click here
| NG | | REPLACE FUEL SENDER GAUGE ASSEMBLY |
|
| 3. | CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY AND BODY GROUND) |
(a) Disconnect the I10 combination meter assembly connector.
(b) Disconnect the b2 fuel sender gauge assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I10-27 (FR) - b2-1 (FS) | Always | Below 1 Ω |
| I10-28 (FE) - b2-2 (FE) | Always | Below 1 Ω |
| I10-31 (ES) - Body ground | Always | Below 1 Ω |
| I10-27 (FR) or b2-1 (FS) - Body ground | Always | 10 kΩ or higher |
| I10-28 (FE) or b2-2 (FE) - Body ground | Always | 10 kΩ or higher |
| OK | | REPLACE COMBINATION METER ASSEMBLY |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
Open in Turn Signal Circuit (B1507,B1508)
DESCRIPTION These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light cir
Lost Communication with EV ECU (U0100,U0129,U0131,U0142,U0151,U0163,U0182,U023A)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area U0100 Lost Communication with EV ECU Both conditions are met:
IG voltage is 10.5 V or higher.
No communica
Speedometer Malfunction
DESCRIPTION The combination meter assembly receives vehicle speed signals from the brake booster with master cylinder assembly (skid control ECU) via the CAN communication line. The wheel speed sensor
SEE MORE:
Noise Occurs or Sound Skips when Portable Player Plays
CAUTION / NOTICE / HINT HINT:
Perform this check with the portable player volume set at an appropriate level.
Make sure that there are no obstructions between the portable player and radio receiver assembly that may block signals, and that the portable player and radio receiver assembly are not
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL NOTICE: After the power switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the power switch off, be sure to wait for the time specified in th
