Lexus NX manuals

Lexus NX: HD Radio Tuner Malfunction (B1551,B15A0,B15B3,B15B5,B15B7,B15BA,B15F9)

Lexus NX Service Manual / Audio & Visual & Telematics / Audio / Video / Audio And Visual System / HD Radio Tuner Malfunction (B1551,B15A0,B15B3,B15B5,B15B7,B15BA,B15F9)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the radio receiver assembly

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B1551

HD Radio Tuner Malfunction

When one of the conditions below is met:

  • "HD Radio" tuner decoder malfunction
  • "HD Radio" tuner audio output section malfunction
  • "HD Radio" tuner decoder RF/IF malfunction

Radio receiver assembly

B15A0

LAN Master Malfunction

When either of the following conditions is met:

  • Bus malfunction
  • EEPROM error

Radio receiver assembly

B15B3

Radio Tuner Malfunction

When any of the following conditions is met:

  • AM tuner PLL is unlocked
  • FM tuner PLL is unlocked
  • Tuner malfunction

Radio receiver assembly

B15B5

DVD Changer Malfunction

When any of the following conditions is met:

  • Mechanism drive signal malfunction
  • Load/Eject malfunction
  • Read mechanism malfunction
  • Mechanical malfunction

Radio receiver assembly

B15B7

Bluetooth Module Malfunction

"Bluetooth" module malfunction

Radio receiver assembly

B15BA

XM Tuner Malfunction

When one of the conditions below is met:

  • Internal IC malfunction
  • Tuner malfunction

Radio receiver assembly

B15F9

UART Communication Malfunction(for A/C)

When either of the following conditions is met:

  • Open in UART communication line is detected based on radio receiver assembly activation failure
  • Open in UART communication line is detected based on communication error

Radio receiver assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the radio receiver assembly, always replace it with a new one.

If a radio receiver assembly which was installed to another vehicle is used, the following may occur:

  • A communication malfunction DTC may be stored.
  • The radio receiver assembly may not operate normally.

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here

PROCEDURE

1.

CHECK DTC

(a) Clear the DTCs.

Click here

Body Electrical > Navigation System > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Click here

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE RADIO RECEIVER ASSEMBLY

READ NEXT:

 Touch Pad Sensor Malfunction (B1559)

DESCRIPTION This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad sensor malfunction. DTC No.

 Touch Pad Vibration Driver Malfunction (B155A)

DESCRIPTION This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad vibration driver malfunction.

 Touch Pad Memory Module Malfunction (B155B)

DESCRIPTION This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad memory module malfunction.

SEE MORE:

 Components

COMPONENTS ILLUSTRATION *1 COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY *2 FRONT FENDER TO COWL SIDE SEAL LH *3 FRONT FENDER TO COWL SIDE SEAL RH *4 FRONT WIPER ARM HEAD CAP *5 FRONT WIPER ARM LH *6 FRONT WIPER ARM RH *7 NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP *8 WI

 Rear Door LH Entry Lock Function does not Operate

DESCRIPTION If the entry lock function does not operate for the rear door LH only, but the entry unlock function operates, the request code is being transmitted properly from the rear door LH. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (

© 2016-2025 Copyright www.lexunx.com