Lexus NX: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the intelligent clearance sonar system.
- *: Use the Techstream.
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. | CUSTOMER PROBLEM ANALYSIS |
|
| 3. | INSPECT AUXILIARY BATTERY VOLTAGE |
(a) Measure the auxiliary battery voltage.
Standard voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
|
| 4. | CHECK CAN COMMUNICATION SYSTEM* |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here .gif)
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
| B | .gif) | GO TO CAN COMMUNICATION SYSTEM |
|
| 5. | PROBLEM SYMPTOM CONFIRMATION |
|
| 6. | CHECK DTC* |
(a) Check for DTCs.
Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output (Problem symptom does not occur) | B |
| DTCs are not output (Problem symptom occurs) | C |
| B | | GO TO STEP 8 |
| C | | GO TO STEP 9 |
|
| 7. | DIAGNOSTIC TROUBLE CODE CHART (INTELLIGENT CLEARANCE SONAR SYSTEM) |
(a) Refer to Diagnostic Trouble Code Chart.
Click here
NOTICE:
The clearance warning ECU assembly outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the intelligent clearance sonar system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.
| System | Proceed to |
|---|---|
| Intuitive Pariking Assist System (w/ Intelligent Clearance Sonar System) | |
| NEXT | | GO TO STEP 11 |
| 8. | SYMPTOM SIMULATION |
(a) Refer to Symptom Simulation.
Click here
|
| 9. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
| B | | GO TO STEP 11 |
|
| 10. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check
Click here
(b) Terminals of ECU
Click here
(c) Data List / Active Test
Click here
|
| 11. | CIRCUIT INSPECTION |
|
| 12. | IDENTIFICATION OF PROBLEM |
|
| 13. | REPAIR OR REPLACE |
|
| 14. | CONFIRMATION TEST |
| NEXT | | END |
READ NEXT:
Operation Check
OPERATION CHECK ICS OFF INDICATOR LIGHT OPERATION CHECK (a) Turn the power switch on (IG). (b) Turn the intelligent clearance sonar system off and confirm that the ICS OFF indicator in the combination
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE INTELLIGENT CLEARANCE SONAR SYSTEM (a) Customizing with the Techstream. NOTICE:
When the customer requests a change in a function, first make sure that the function c
Calibration
CALIBRATION NOTICE: When any of the following parts have been replaced, perform adjustment shown in the following table. If not, the intelligent clearance sonar system may not operate correctly. PRECA
SEE MORE:
Lost Communication with Airbag System Control Module (P3107-213)
DESCRIPTION The hybrid vehicle control ECU detects a problem in the collision signal line from the airbag ECU assembly and alerts the driver. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P3107-213 Lost Communication with Airbag System Control Mo
System Description
SYSTEM DESCRIPTION WIRELESS DOOR LOCK CONTROL SYSTEM The wireless door lock control system can be used to lock and unlock all doors from a distance. The system is controlled by an electrical key transmitter sub-assembly which sends radio waves to the door control receiver. The certification ECU (sma
