- Hybrid control system starting: Hybrid control system cannot be started next time
- Hybrid control system stopped: Hybrid control system cannot be started
Lexus NX: ID BOX EEPROM Malfunction (B2790)
Lexus NX Service Manual / Vehicle Interior / Theft Deterrent / Keyless Entry / Immobiliser System / ID BOX EEPROM Malfunction (B2790)
DESCRIPTION
When an internal malfunction occurs in the ID code box (immobiliser code ECU), the certification ECU (smart key ECU assembly) stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2790 | ID BOX EEPROM Malfunction | An internal malfunction occurs in the ID code box (immobiliser code ECU) (EEPROM access malfunction). (1 trip detection logic*) |
| DTC output confirmation operation:
|
- *: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2790 | - |
CAUTION / NOTICE / HINT
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
Before replacing the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), refer to Registration.
Click here
.gif)
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
PROCEDURE
| 1. | REPLACE ID CODE BOX (IMMOBILISER CODE ECU) |
(a) Replace the ID code box (immobiliser code ECU) with a new one.
Click here
|
.gif)
| 2. | CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Smart Access > Clear DTCs
|
| 3. | REGISTER RECOGNITION CODE |
(a) Register the recognition codes in the ECUs.
Click here
|
| 4. | REGISTER ECU COMMUNICATION ID |
(a) Register the ECU communication ID.
Click here
|
| 5. | CHECK FOR DTC |
(a) Perform "DTC Output Confirmation Operation" procedure.
(b) Check for DTCs.
Body Electrical > Smart Access > Trouble CodesOK:
DTC B2790 is not output.
| OK | .gif) | END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE) |
| NG | | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
READ NEXT:
Engine Immobiliser System Malfunction (B2799-790)
DESCRIPTION When there is a communication malfunction between the hybrid vehicle control ECU and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the hybrid vehicle
Engine Immobiliser System Communication Line High Fixation (B279A-186)
DESCRIPTION When the communication line (IMI - EFIO) between the hybrid vehicle control ECU and ID code box (immobiliser code ECU) is stuck high, the hybrid vehicle control ECU stores this DTC. DTC
Engine Immobiliser System Presence Detection (B279C-185)
DESCRIPTION If a hybrid vehicle control ECU that is incompatible with the immobiliser system is installed, the hybrid vehicle control ECU stores this DTC. DTC No. Detection Item DTC Detection C
SEE MORE:
AV Signal Stoppage (Low Battery Voltage) (B158F)
DESCRIPTION This DTC is stored when a video or audio signal is interrupted due to auxiliary battery voltage input to the radio receiver assembly dropping temporarily. DTC No. Detection Item DTC Detection Condition Trouble Area B158F AV Signal Stoppage (Low Battery Voltage) A video o
Sensor Frozen Indication (Dirty or Frozen)
DESCRIPTION When the ultrasonic sensor is dirty or frozen, "Parking Assist Unavailable Clean Parking Assist Sensor" is displayed on the multi-information display in the combination meter assembly. PROCEDURE 1. CHECK FOR DTC (a) Clear the DTCs. Click here Body Electrical > Advanced Park
© 2016-2025 Copyright www.lexunx.com
