Lexus NX: Installation
INSTALLATION
PROCEDURE
1. INSTALL RADIO RECEIVER ASSEMBLY
2. INSTALL NAVIGATION ECU
Click here .gif)
3. INSTALL NO. 1 RADIO BRACKET
(a) w/ Navigation System
(1) Install the No. 1 radio bracket with the 5 screws.
(b) w/o Navigation System
(1) Install the No. 1 radio bracket with the 3 screws.
4. INSTALL NO. 2 RADIO BRACKET
(a) w/ Navigation System
(1) Install the No. 2 radio bracket with the 5 screws.
(b) w/o Navigation System
(1) Install the No. 2 radio bracket with the 3 screws.
5. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET
(a) Connect each connector.
(b) Attach the 4 clips to temporarily install the radio receiver assembly with bracket.
(c) Install the radio receiver assembly with bracket with the 4 bolts.
6. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
Click here
7. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY
Click here
8. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Click here
9. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Click here
10. INSTALL NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
11. INSTALL NO. 1 SWITCH HOLE BASE
Click here
12. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Click here
13. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
14. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
15. INSTALL INSTRUMENT SIDE PANEL LH
Click here
16. INSTALL INSTRUMENT SIDE PANEL RH
Click here
17. INSTALL UPPER NO. 2 CONSOLE PANEL GARNISH
Click here
18. INSTALL UPPER NO. 1 CONSOLE PANEL GARNISH
Click here
19. INSTALL UPPER REAR CONSOLE PANEL
Click here
20. INSTALL CONSOLE ARMREST ASSEMBLY
Click here
21. INSTALL MULTI-DISPLAY ASSEMBLY WITH BRACKET
Click here
22. INSTALL INSTRUMENT PANEL FINISH PLATE
Click here
23. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
24. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click here
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
25. CHECK SRS WARNING LIGHT
Click here
26. INSTALL DECK FLOOR BOX LH
Click here
27. INSTALL REAR DECK FLOOR BOX
Click here
28. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Click here
29. INSTALL DECK BOARD ASSEMBLY
Click here
READ NEXT:
Components
COMPONENTS ILLUSTRATION *A for 8 Speakers *B for 10 Speakers *C for 14 Speakers - - *1 REAR DOOR INSIDE HANDLE BEZEL PLUG LH *2 REAR DOOR TRIM BOARD SUB-ASSEMBLY LH *
Removal
REMOVAL CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE 1. REMOVE REAR DOOR TRIM COVER LH Click here 2
SEE MORE:
Lock Function does not Operate (Close &)
DESCRIPTION The door control switch signal is sent to the multiplex network door ECU. If the power back door system does not operate when the door control switch is operated, the door control switch circuit may be malfunctioning. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: If the replacement, re
Display Disconnected (B15D6)
DESCRIPTION The multi-display assembly and radio receiver assembly are connected by the AVC-LAN communication line. This DTC is stored when an AVC-LAN communication error occurs between the multi-display assembly and radio receiver assembly. DTC No. Detection Item DTC Detection Condition Tr
