Lexus NX: Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click here

PROCEDURE

1. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY

2. INSTALL NO. 2 AMPLIFIER BRACKET

(a) Install the No. 2 amplifier bracket with the 2 screws.

3. INSTALL NO. 1 AMPLIFIER BRACKET

(a) Install the No. 1 amplifier bracket with the 2 screws.

4. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

(a) for 10 Speakers:

(1) Attach the guide and install the stereo component amplifier assembly with bracket with the 3 bolts.

(2) Connect the 2 connectors.

(3) Attach the claw to lock the connector lock.

(b) for 14 Speakers:

(1) Attach the guide and install the stereo component amplifier assembly with bracket with the 3 bolts.

(2) Connect the 2 connectors.

(3) Attach the claw to lock the connector lock.

5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

Click here

6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Click here

7. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

Click here

8. INSTALL ROPE HOOK ASSEMBLY

Click here

9. INSTALL UPPER DECK TRIM SIDE BOARD RH

Click here

10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

Click here

11. INSTALL REAR DOOR SCUFF PLATE RH

Click here

12. INSTALL REAR FLOOR FINISH PLATE

Click here

13. INSTALL NO. 2 TOOL BOX SUB-ASSEMBLY

Click here

14. INSTALL NO. 1 TOOL BOX SUB-ASSEMBLY

Click here

15. INSTALL DECK FLOOR BOX RH

Click here

16. INSTALL DECK FLOOR BOX LH

Click here

17. INSTALL SPARE TIRE

Click here

18. INSTALL REAR DECK FLOOR BOX

Click here

19. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

Click here

20. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

Click here

21. INSTALL DECK BOARD ASSEMBLY

Click here

22. INSTALL TONNEAU COVER ASSEMBLY

Click here

23. INSTALL REAR SEAT ASSEMBLY (for Power Seat)

Click here

24. INSTALL REAR SEAT ASSEMBLY (for Manual Seat)

Click here

READ NEXT:

 Stereo Jack Adapter Assembly

ComponentsCOMPONENTS ILLUSTRATION *A w/ Navigation System - - *1 NO. 1 STEREO JACK ADAPTER ASSEMBLY *2 NO. 3 BOX PANEL ILLUSTRATION *A w/o Navigation System - - *

 Window Glass Antenna Wire

On-vehicle InspectionON-VEHICLE INSPECTION PROCEDURE 1. INSPECT WINDOW GLASS ANTENNA WIRE (a) Check for continuity of the antenna. HINT: Check for continuity at the center of each antenna wire as

 Cellular Communication

SEE MORE:

 Vehicle Control History

VEHICLE CONTROL HISTORY NOTICE: When checking the vehicle control history, make sure to record the output histories. Then, remove the histories and recheck the output histories again. CHECK VEHICLE CONTROL HISTORY (PRE-COLLISION SYSTEM) (a) Connect the Techstream to the DLC3. (b) Turn the power swit

 Inspection

INSPECTION PROCEDURE 1. INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 1 (OSL) - 2 (OSLE) Not pressed 950 to 1050 Ω 1 (OSL) - 2 (OSLE) P

© 2016-2025 Copyright www.lexunx.com