Lexus NX: Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
  • w/ Pre-collision System:

    When replacing the forward recognition camera, make sure to replace it with a new one.

  • Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
  • If the main body ECU (multiplex network body ECU) is replaced, refer to registration.
  • After replacing the radio receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SXM System).
  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Meter Gauge

Symptom

Suspected Area

Link

Speedometer malfunction

Refer to "Speedometer Malfunction"

Tachometer malfunction

Refer to "Tachometer Malfunction"

Fuel receiver gauge malfunction

(Fuel receiver gauge is currently malfunctioning, or was malfunctioning in the past)

Refer to "Fuel Receiver Gauge Display Malfunction"

Engine coolant temperature receiver gauge malfunction

Refer to "Engine Coolant Temperature Receiver Gauge Malfunction"

Hybrid system indicator malfunction

Refer to "Hybrid System Indicator Malfunction"

Warning Light or Indicator Light

Symptom

Suspected Area

Link

Turn indicator light does not come on (Turn signal light operates normally)

Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator]

Perform Data List [Turn Signal Switch (Right), Turn Signal Switch (Left)]

Combination meter assembly

Front fog indicator light does not come on (Front fog light operates normally)

CAN communication system

Perform Active Test [Indicat. Lamp Fr FOG]

Combination meter assembly

Main body ECU (multiplex network body ECU)

High beam indicator light does not come on (High beam headlight operates normally)

CAN communication system

Perform Active Test [Indicat. Lamp Beam]

Combination meter assembly

Main body ECU (multiplex network body ECU)

Automatic high beam indicator light does not come on (w/ Automatic High Beam System)

CAN communication system

Check indicator/warning light

Perform Active Test [Automatic High Beam Indicator]

Automatic high beam system

Combination meter assembly

Taillight indicator light does not come on (Taillight operates normally) (with km/h units)

CAN communication system

Perform Active Test [Indicat. Lamp Tail]

Main body ECU (multiplex network body ECU)

Combination meter assembly

Headlight indicator light does not come on (Headlight operates normally) (with mph units)

CAN communication system

Perform Active Test [Indicat. Lamp Tail]

Main body ECU (multiplex network body ECU)

Combination meter assembly

Driver seat belt warning light malfunction

CAN communication system

Perform Active Test [Driver Side Seat Belt]

Proceed to "Driver Side Seat Belt Warning Light does not Operate"

Combination meter assembly

Front passenger side seat belt warning light malfunction

CAN communication system

Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction"

Combination meter assembly

SRS warning light malfunction

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Lamp Airbag]

Proceed to "SRS Warning Light Remains ON"

Proceed to "SRS Warning Light does not Come ON"

Combination meter assembly

Master warning light (Other systems operate normally)

Check indicator/warning light

Perform Active Test [Master Warning]

Combination meter assembly

MIL (Malfunction indicator lamp) malfunction

CAN communication system

Check indicator/warning light

Perform Active Test [Check Engine Indicator]

Proceed to "MIL Circuit"

Combination meter assembly

EPS warning light malfunction

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. EPS]

Proceed to "Power Steering Warning Light Circuit" (for Manual Tilt and Manual Telescopic Steering Column)

Proceed to "Power Steering Warning Light Circuit" (for Power Tilt and Power Telescopic Steering Column)

Combination meter assembly

Brake warning light malfunction

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Lamp Brake]

Proceed to "Brake Warning Light Remains ON"

Proceed to "Brake Warning Light does not Come ON"

Combination meter assembly

Cruise indicator light does not come on

CAN communication system

Proceed to "Cruise Main Indicator Light Circuit"

Combination meter assembly

SET indicator light does not come on

CAN communication system

Proceed to "Cruise SET Indicator Light Circuit"

Combination meter assembly

Radar cruise indicator light does not come on (w/ Dynamic Radar Cruise Control System)

CAN communication system

Proceed to "Cruise Main Indicator Light Circuit"

Combination meter assembly

Lane tracing assist indicator light does not come on (w/ Lane tracing assist system)

CAN communication system

Proceed to "Indicator Circuit"

Combination meter assembly

Steering indicator light does not come on (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

Tire pressure warning light malfunction

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Tire Pressure Warning System]

Proceed to "Tire Pressure Warning Light Circuit"

Combination meter assembly

Fuel level warning light does not come on (Fuel receiver gauge operates normally)

Perform Active Test [Indicat. Lamp Fuel]

Combination meter assembly

ABS warning light malfunction

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Lamp ABS]

Proceed to "ABS Warning Light Remains ON"

Proceed to "ABS Warning Light does not Come ON"

Combination meter assembly

VSC OFF indicator light malfunction

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. VSC OFF]

Proceed to "VSC OFF Switch Circuit"

Combination meter assembly

Slip indicator light does not come on

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Lamp Slip]

Proceed to "Slip Indicator Light Remains ON"

Proceed to "Slip Indicator Light does not Come ON"

Combination meter assembly

EPB* warning light does not come on

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Park]

Combination meter assembly

Parking brake ECU assembly

PCS OFF indicator light malfunction (w/ Pre-collision System)

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Precrash]

Pre-collision system

Combination meter assembly

Forward recognition camera

Clearance sonar indicator light does not come on (w/ Intuitive Parking Assist System)

CAN communication system

Perform Active Test [Indicat. INTUITIVE P/A LCD]

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

ICS OFF indicator light malfunction (w/ Intelligent Clearance Sonar System)

CAN communication system

Intelligent clearance sonar system

Combination meter assembly

Clearance warning ECU assembly

Eco mode indicator light does not come on

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Sport mode indicator light does not come on

CAN communication system

Combination meter assembly

Hybrid vehicle control ECU

Brake hold standby indicator light does not come on

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Brake Hold]

Proceed to "Brake Hold Standby Indicator Light Circuit"

Combination meter assembly

Brake hold operated indicator light does not come on

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Hold]

Proceed to "Brake Hold Operated Indicator Light Circuit"

Combination meter assembly

ECB* warning light does not come on

CAN communication system

Check indicator/warning light

Perform Active Test [Indicat. Lamp ECB]

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

READY indicator light does not come on

CAN communication system

Perform Active Test [Indicat. Ready (HV)]

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

EV indicator light does not come on

CAN communication system

Check customize setting

Perform Active Test [EV Mode Indicator]

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

EV mode indicator light does not come on

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Multi-information Display

Symptom

Suspected Area

Link

"Opening" display malfunction

Combination meter assembly

"Each door ajar" display malfunction (Door courtesy switch, back door courtesy switch or hood courtesy switch is normal)

CAN communication system

Combination meter assembly

Main body ECU (multiplex network body ECU)

"Outside temp" display malfunction*A

Proceed to "Ambient Temperature Display System"

Icy street warning display malfunction

CAN communication system

Air conditioning system

Combination meter assembly

Air conditioning amplifier assembly

"Windshield Washer Fluid Low" display malfunction

Proceed to "Washer Fluid Level Warning Switch Circuit"

"Current fuel consumption" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Average fuel consumption (After refuel)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Average fuel consumption (After reset)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Average fuel consumption (After start)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Average speed (After start)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Average speed (After reset)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Elapsed time (After reset)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Elapsed time (After start)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Distance (Range)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Distance (After start)" display malfunction (Combination meter assembly operates normally)

Combination meter assembly

"Energy flow display" display malfunction

CAN communication system

Hybrid control system

Hybrid battery system

Combination meter assembly

Tire pressure display malfunction

Tire pressure warning system

Combination meter assembly

"Navigation tab" display malfunction (except 8 Speakers)

Navigation system

Audio and visual system

Combination meter assembly

Radio receiver assembly

"Audio tab" display malfunction

Navigation system

Audio and visual system

Combination meter assembly

Radio receiver assembly

"Radar cruise control / Lane tracing assist displayed tab" display malfunction (w/ Dynamic Radar Cruise Control System or Lane tracing assist system)

Combination meter assembly

Forward recognition camera

"Message tab" display malfunction

Combination meter assembly

"Setting tab" display malfunction

Combination meter assembly

"Shift selector" display malfunction

Perform Active Test [A/T Indicator Operation 1, A/T Indicator Operation 2, A/T Indicator Operation 3]

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"SPORT indicator" display malfunction

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"SPORT S indicator" display malfunction

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"SPORT S+ indicator" display malfunction

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Fuel Low" display malfunction (Fuel receiver gauge operates normally)

Combination meter assembly

"AWD TEST MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"CDY-2" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"CDY-4" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"2WD MAINTENANCE MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"AWD MAINTENANCE MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"2WD CERTIFICATION MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"AWD CERTIFICATION MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"AWD System Malfunction 2WD Mode Engaged Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"AWD System Overheated 2WD Mode Engaged" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"AWD System Overheated Switching to 2WD Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD)

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Push and Hold Power Switch for Emergency Stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Shift to N and Press Power Switch to Restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Power Turned Off to Save Battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Key Not Detected Check Key Location" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Smart Access System Malfunction See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Turn Off Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Key Left inside Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Depress Brake and Then Touch Key to Power Switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Depress Brake and Power to Start" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Key Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"IGNITION ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Steering Wheel Lock Press Power Switch while Turning Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Steering lock system

Combination meter assembly

Certification ECU (smart key ECU assembly)

"Shift to P Before Exiting Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"To Start Vehicle, Put Shift Lever into P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid System Stopped Shift to P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid System Stopped Stop in a Safe Place" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Switch to Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Intelligent clearance sonar system

Combination meter assembly

Clearance warning ECU assembly

"Object Detected Acceleration Reduced" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Intelligent clearance sonar system

Combination meter assembly

Clearance warning ECU assembly

"Accelerator Stuck Depress Brake to Stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Release Accelerator" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid System Malfunction Do Not Be Towed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Shift Is in N Release Accelerator Before Shifting" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Depress Brake When Vehicle Is Stopped Hybrid System May Overheat" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid Battery Low Hybrid System Stopped Shift to P and Restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid System Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Check Engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid Battery System Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Accelerator System Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid Battery Low Shift Out of N to Recharge" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Check Engine Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

"Check Engine Reduced Engine Power Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

"Engine Coolant Temp High Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

"Oil Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units)

CAN communication system

SFI system

Combination meter assembly

ECM

"Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units)

CAN communication system

SFI system

Combination meter assembly

ECM

"Injector Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units)

CAN communication system

SFI system

Combination meter assembly

ECM

"Oil Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units)

CAN communication system

SFI system

Combination meter assembly

ECM

"Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units)

CAN communication system

SFI system

Combination meter assembly

ECM

"Injector Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units)

CAN communication system

SFI system

Combination meter assembly

ECM

"Drive-Start Control Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Brake Override Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Accelerator and Brake Pedals Depressed Simultaneously" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Hybrid System Overheated Reduced Output Power" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Maintenance required for hybrid battery cooling parts at your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Aux Battery Low See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Unavailable System Warming Up" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Unavailable Hybrid Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Unavailable Speed Range Exceeded" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Unavailable Reduce Acceleration to Activate" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Deactivated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Deactivated Speed Range Exceeded" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Deactivated Hybrid Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"EV Mode Deactivated Accelerator Depressed Too Far" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Low Oil Pressure Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

Engine oil pressure switch

Harness or connector

-

Combination meter assembly

"Antilock Brake System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Braking Power Low Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Traction Control Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Warning Depress Brake on Slope" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Less Effective during Icy Conditions" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Active Depress Brake and Switch to Deactivate" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Unavailable Driver Door Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Unavailable Driver Seat Belt Unbuckled" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Unavailable Hood or Trunk Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Depress Brake to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Close Driver Door to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Fasten Driver Seat Belt to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Braking Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Release Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Vehicle May Roll Shift to P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Release Parking Brake while Depressing Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Parking Brake Overheated Parking Brake Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Parking Brake Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Electronic Parking Brake Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Parking Brake Activated Release Before Driving" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Brake Hold Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Brake Hold Deactivted" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Automatic Mode On Shift Operation Sets or Releases Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Automatic Mode Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

"Power Steering Malfunction Steering Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Power steering system (for Manual Tilt and Manual Telescopic Steering Column)

Power steering system (for Power Tilt and Power Telescopic Steering Column)

Combination meter assembly

Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column)

Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column)

"Steering Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Power steering system (for Manual Tilt and Manual Telescopic Steering Column)

Power steering system (for Power Tilt and Power Telescopic Steering Column)

Combination meter assembly

Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column)

Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column)

"Power Steering Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Power steering system (for Manual Tilt and Manual Telescopic Steering Column)

Power steering system (for Power Tilt and Power Telescopic Steering Column)

Combination meter assembly

Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column)

Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column)

"Hybrid System Stopped Steering Power Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Power steering system (for Manual Tilt and Manual Telescopic Steering Column)

Power steering system (for Power Tilt and Power Telescopic Steering Column)

Combination meter assembly

Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column)

Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column)

"SRS Airbag System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Airbag system

Combination meter assembly

Airbag ECU assembly

"Turn Lights Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Lighting system (for Triple Beam Headlight)

Lighting system (for Single Beam Headlight)

Combination meter assembly

Main body ECU (multiplex network body ECU)

"Headlight System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Lighting system (for Triple Beam Headlight)

Lighting system (for Single Beam Headlight)

Automatic high beam level control system (w/ Automatic High Beam Level Control System)

Automatic high beam system (w/ Automatic High Beam System)

Combination meter assembly

Headlight light control ECU sub-assembly

"To Activate Auto High Beam, Switch Headlights to High Beam" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Automatic High Beam System)

CAN communication system

Automatic high beam system

Combination meter assembly

Headlight light control ECU sub-assembly

Pre-collision display is not displayed (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"BRAKE !" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"VSC Turned Off Pre-collision Brake System Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"Pre-collision System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"Pre-collision System Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"Pre-collision System Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"Front Camera Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"Front Camera Vision Blocked Clean and Demist Windshield" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"RADAR READY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"Operate Cruise Lever or Accelerator Pedal to Resume" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"CRUISE NOT AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"PRECEDING VEHICLE MOVEMENT" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"WAITING" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"Mute PKSA Temporarily" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"PKSA Muted Temporarily" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"ADJUSTING LTA CAMERA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Hold Steering Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"LTA Steering Assist Unavailable Hold Steering Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

Lane tracing assist display is not displayed (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Lane tracing assist Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Lane tracing assist Unavailable Camera Overheated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"LTA Steering Assist Deactivated Warnings Available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Lane tracing assist Turned On Steering Assist Active" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Lane tracing assist Turned On Steering Assist Inactive" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Lane tracing assist Unavailable Below Approx 50km/h" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Lane tracing assist Unavailable Below Approx 32MPH" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Lane tracing assist Unavailable at Current Speed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

Dynamic radar cruise display is not displayed (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"Would You Like to Take a Rest?" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Please Take a Rest" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system)

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"ADJUSTING FRONT RADAR BEAM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"CHECKING CRUISE CONTROL C/D" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Hybrid vehicle control ECU

Forward recognition camera

"CHECKING CRUISE CONTROL BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Hybrid vehicle control ECU

Forward recognition camera

"Radar Cruise Control Unavailable Clean Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"Radar Cruise Control Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"Radar Cruise Control Unavailable Depress Brake to Resume Driving" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"Radar Cruise Active Please Pay Attention to Other Vehicles" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System)

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"Cruise Control Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Hybrid vehicle control ECU

Forward recognition camera

"Cruise Control Fault Press Brake to Deactivate Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Hybrid vehicle control ECU

Forward recognition camera

Intuitive parking assist display is not displayed (w/ Intuitive Parking Assist System)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"Parking Assist Malfunction Vist Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"Parking Assist Unavailable Clean Parking Assist Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"Blind Spot Monitor Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System)

CAN communication system

Blind spot monitor system

Combination meter assembly

Blind spot monitor sensor LH

"Blind Spot Monitor System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System)

CAN communication system

Blind spot monitor system

Combination meter assembly

Blind spot monitor sensor LH

"Moon Roof Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof System)

CAN communication system

Sliding roof system

Combination meter assembly

Main body ECU (multiplex network body ECU)

"Window Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Power window control system

Combination meter assembly

Main body ECU (multiplex network body ECU)

"Window or Moon Roof Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof System)

CAN communication system

Power window control system

Sliding roof system

Combination meter assembly

Main body ECU (multiplex network body ECU)

"High Power Consumption Partial Limit On AC/Heater Operation" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Air conditioning system

Combination meter assembly

Air conditioning amplifier assembly

"Theft Sensor Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Theft deterrent system

Combination meter assembly

Main body ECU (multiplex network body ECU)

"Theft Sensor Turned On" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Theft deterrent system

Combination meter assembly

Main body ECU (multiplex network body ECU)

"Acoustic Vehicle Alerting System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Acoustic vehicle alerting system

Combination meter assembly

Vehicle approaching speaker assembly

Dead pixels on multi-information display

Perform Active Test [Meter Display 1]

Combination meter assembly

Multi-information display customize setting does not operate

Combination meter assembly

"ADJUSTING FORWARD CAMERA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

"CHECKING PCS BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"WRITE ZERO-POINT OF STEERING ANGLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive parking assist system)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"END OF ADJUSTMENT" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive parking assist system)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"MEMORY ERROR" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive parking assist system)

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"Headlight System Uninitialized. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Lighting system (for Triple Beam Headlight)

Lighting system (for Single Beam Headlight)

Combination meter assembly

Headlight light control ECU sub-assembly LH

"Press Brake Pedal" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Intuitive parking assist system

Combination meter assembly

Clearance warning ECU assembly

"Check Fuel Cap" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

"Traction Battery Needs to be Protected. Shift into P to Restart." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Traction Battery Needs to be Protected. Refrain From the Use of N Position." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Engine Maintenance Required. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

"Radar Cruise Control Unavailable. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

ECM

"LTA Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Lane tracing assist system

Combination meter assembly

Forward recognition camera

"Front Camera Unavailable. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Pre-collision system

Combination meter assembly

Forward recognition camera

"Braking Power Low. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically Controlled Brake System

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"Turn Lights Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Lighting system (for Triple Beam Headlight)

Lighting system (for Single Beam Headlight)

Combination meter assembly

Main body ECU (multiplex network body ECU)

"Brake Hold Deactivated. Parking Brake Automatically Applied." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Electronically Controlled Brake System

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

"RSA malfunction. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Road sign assist system

Combination meter assembly

Forward recognition camera

"Exhaust Filter Full. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

"Aux Battery Low. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

"Exhaust Filter Full. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

"Exhaust Filter Regeneration In Process" message is displayed when it should not be, not displayed when it should be, or not displayed correctly

CAN communication system

SFI system

Combination meter assembly

ECM

*A: Items for consideration regarding ambient temperature display value

  • The display value of the ambient temperature around the sensor changes due to the effects of heat radiated from the engine room and vehicle speed.
  • Depending on the driving status, the ambient temperature of the air surrounding the vehicle and the displayed value are different and the speed at which the displayed value updates is delayed. However, this is not a malfunction. When the vehicle is stopped or being driven at a low speed, the value is not updated to a higher temperature in order to minimize the effects of the radiated heat from the engine on the auto air conditioning control. Since the same adjustment occurs while the vehicle is being driven at medium to high speeds, updating to a higher temperature is delayed. However, the value is updated to a lower temperature regardless of the vehicle speed.
Buzzer

Symptom

Suspected Area

Link

All buzzers do not operate normally

Combination meter assembly

Shift reject buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Engine coolant temperature buzzer does not operate

SFI system

Combination meter assembly

ECM

Seat belt warning buzzer does not operate (Front seat belt, Rear seat belt warning light operates normally)

Check customize setting

Combination meter assembly

Engine immobiliser certification buzzer does not operate

Immobiliser system

Combination meter assembly

Certification ECU (smart key ECU assembly)

Smart access system with push-button start warning buzzer does not operate

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

Power switch operation while driving warning buzzer does not operate

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

Restart while driving notification buzzer does not operate

Smart access system with push-button start (for Entry Function)

Smart access system with push-button start (for Start Function)

Combination meter assembly

Certification ECU (smart key ECU assembly)

Vehicle roll-away notification buzzer does not operate (Speedometer and tachometer operate normally)

Combination meter assembly

ECM

Driving with any door opened warning buzzer does not operate (Open door warning light and speedometer operate normally)

Combination meter assembly

PKB-ON driving warning buzzer does not operate (Brake warning light and speedometer operate normally)

Combination meter assembly

EPS warning buzzer does not operate (Power steering system operates normally)

Combination meter assembly

Dynamic radar cruise control low speed cancel buzzer does not operate (w/ Dynamic Radar Cruise Control System)

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

Radar cruise low speed range preceding vehicle lost buzzer does not operate (w/ Dynamic Radar Cruise Control System)

Dynamic radar cruise control system

Combination meter assembly

Forward recognition camera

Multi-information display warning buzzer does not operate

Combination meter assembly

Flasher buzzer does not operate (Turn indicator light normally)

Check customize setting

Combination meter assembly

Oil pressure warning buzzer does not operate

Engine oil pressure warning switch

Harness or connector

-

Combination meter assembly

Vehicle stability control sideways sliding warning buzzer does not operate

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

Brake system low braking force warning buzzer does not operate

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

Brake system temperature rise / active test buzzer does not operate

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

Temperature warning/CRAWL cancel warning buzzer does not operate

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

Hill-start assist control buzzer (Reset) malfunction

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

Hill-start assist control buzzer (Set) malfunction

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

Lane tracing assist cancel buzzer does not operate (w/ Lane tracing assist system)

Lane tracing assist system

Combination meter assembly

Forward recognition camera

Lane tracing assist warning buzzer does not operate (w/ Lane tracing assist system)

Lane tracing assist system

Combination meter assembly

Forward recognition camera

Lane tracing assist hands off steering wheel warning buzzer does not operate (w/ Lane tracing assist system)

Lane tracing assist system

Combination meter assembly

Forward recognition camera

Brake hold control unreleased warning buzzer does not operate

Electronically controlled brake system

Combination meter assembly

Brake booster with master cylinder assembly (skid control ECU)

EPB* cancel buzzer does not operate

Electrical parking brake system

Combination meter assembly

Parking brake ECU assembly

READY buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

EV reject buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Shift to P position request buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Depress the accelerator pedal with shift position N buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Hybrid control system warning buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

HV battery low voltage buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

HV unit excessive heat notification buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Tow prohibition buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Accelerator hold warning buzzer does not operate

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

Power window / sliding roof warning buzzer malfunction

Power window control system

Sliding roof system (w/ Sliding Roof System)

Combination meter assembly

Main body ECU (multiplex network body ECU)

Light reminder warning buzzer does not operate

Lighting system (for Triple Beam Headlight)

Lighting system (for Single Beam Headlight)

Combination meter assembly

Main body ECU (multiplex network body ECU)

Others

Symptom

Suspected Area

Link

DTCs display malfunction (Other systems operate normally)

Combination meter assembly

Operating light control rheostat does not change light brightness

Refer to "Operating Light Control Rheostat does not Change Light Brightness"

Meter illumination is always dark

CAN communication system

Lighting system (for Triple Beam Headlight)

Lighting system (for Single Beam Headlight)

Combination meter assembly

Main body ECU (multiplex network body ECU)

Operating ODO/TRIP switch does not change ODO/TRIP meter display

Refer to "Odo/Trip Switch Malfunction"

Multi-information display does not change using steering pad switch assembly

Perform Active Test [Multi Switch (Up), Multi Switch (Down), Multi Switch (Menu), Multi Switch (Enter), Multi Switch (Right), Multi Switch (Left)]

Steering pad switch assembly

Spiral cable sub-assembly

Harness or connector

-

Combination meter assembly

Cannot switch between tachometer and hybrid system indicator

Hybrid control system

Combination meter assembly

Hybrid vehicle control ECU

READ NEXT:

 Terminals Of Ecu

TERMINALS OF ECU COMBINATION METER ASSEMBLY (a) Measure the voltage, resistance and waveform according to the value(s) in the table below. Terminal No. (Symbol) Wiring Color Terminal Descripti

 Dtc Check / Clear

DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Combination Meter /

 Freeze Frame Data

FREEZE FRAME DATA FREEZE FRAME DATA (a) Whenever a meter DTC is detected, the combination meter assembly stores the current vehicle state as freeze frame data. CHECK FREEZE FRAME DATA (a) Connect the

SEE MORE:

 All HV Gate Blocking Range/Performance (P321E-318)

DESCRIPTION The hybrid vehicle control ECU sends a block signal to the motor generator control ECU (MG ECU) to shutdown the power supply to the motor. When the system is not in the on (READY) state, it sends an HSDN (MG shutdown signal) signal from the hybrid vehicle control ECU to the motor generat

 Operation Check

OPERATION CHECK CHECK SEAT HEATER (for Front) (a) Turn the power switch on (IG). (b) Check that the indicator illuminates and the surface of the front seat warms up, when the seat heater switch on the air conditioning control assembly is turned on. (c) Check that the front seat surface temperature c

© 2016-2022 Copyright www.lexunx.com