Lexus NX: Removal

REMOVAL

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the forward recognition camera, replace it with a new one.
  • Replace the forward recognition camera if there is any foreign matter on the camera lens.
  • Do not touch the camera lens or the front windshield glass in front of the camera.
  • If the forward recognition camera has been struck or dropped, replace it with a new one.
  • When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Lexus genuine part. If a non-Lexus genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also the dynamic radar cruise control system, front camera system, lane tracing assist system, road sign assist system, pre-collision system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.

PROCEDURE

1. REMOVE NO. 2 FORWARD RECOGNITION COVER

(a) Detach the claw in the direction indicated by the arrow (1) as shown in the illustration.

NOTICE:

If the 2 claws are detached separately they may become damaged. Therefore, remove them at the same time.

Place your finger here

Remove in this Direction (1)

Remove in this Direction (2)

(b) Place your fingers of both hands at the position shown in the illustration and detach the guide in the direction indicated by the arrow (2) in the illustration to remove the No. 2 forward recognition cover.

2. REMOVE NO. 1 FORWARD RECOGNITION COVER

(a) Detach the clip and guide and remove the No. 1 forward recognition cover as shown in the illustration.

Remove in this Direction

NOTICE:

When removing, press the cover parallel to the windshield glass surface and remove.

3. REMOVE FORWARD RECOGNITION LATCH

(a) Detach the claw in the direction indicated by the arrow (1) in the illustration.

Remove in this Direction (1)

Remove in this Direction (2)

(b) Detach the guide in the direction indicated by the arrow (2) in the illustration to remove the forward recognition latch.

4. REMOVE FORWARD RECOGNITION CAMERA

NOTICE:

If the forward recognition camera has been struck or dropped, replace it with a new one.

(a) Disconnect the connector.

Remove in this Direction

NOTICE:

Do not pull the harness forcibly when disconnecting the connector.

(b) Detach the guide and remove the forward recognition camera as shown in the illustration.

NOTICE:

  • Do not apply excessive force.
  • If the forward recognition camera bracket is deformed or damaged, replace it together with the windshield glass.

READ NEXT:

 Installation

INSTALLATION PROCEDURE 1. INSTALL FORWARD RECOGNITION CAMERA NOTICE: When replacing the forward recognition camera, replace it with a new one. If the forward recognition camera has been struck or

 Before Starting Adjustment

BEFORE STARTING ADJUSTMENT CAUTION / NOTICE / HINT NOTICE: When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Lexus genuine part. If a non-

 Adjustment (one Time Recognition)

ADJUSTMENT (ONE TIME RECOGNITION) CAUTION / NOTICE / HINT NOTICE: Make sure to read Before Starting Adjustment before proceeding with work. Click here PROCEDURE 1. SECURE APPROPRIATE AREA FOR PERFOR

SEE MORE:

 Installation

INSTALLATION PROCEDURE 1. INSTALL REAR SEAT CENTER LAP TYPE BELT ASSEMBLY LH (a) Install the rear seat center lap type belt assembly LH with the nut. Torque: 42 N·m {428 kgf·cm, 31 ft·lbf} NOTICE: The anchor part of the rear seat center lap type belt assembly LH must not overlap the protrudin

 Parts Location

PARTS LOCATION ILLUSTRATION *1 POWER STEERING ECU ASSEMBLY *2 ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY - POWER STEERING MOTOR ASSEMBLY - MOTOR ROTATION ANGLE SENSOR - TORQUE SENSOR - ECU WIRE SUB-ASSEMBLY *3 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) *4 NO.

© 2016-2024 Copyright www.lexunx.com