Lexus NX: There is No Sound Made
DESCRIPTION
Based on signals received from each ECU, the vehicle approaching speaker controller outputs warning sounds through the vehicle approaching speaker assembly.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
-
The vehicle proximity notification system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the automatic high beam system after confirming that the communication systems are functioning properly.
Click here
.gif)
PROCEDURE
| 1. | CHECK FOR DTC |
(a) Connect the GTS to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the GTS on.
(d) Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.
Body Electrical > Vehicle Proximity Notification System > Trouble Codes(e) Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1350 is not output | A |
| DTC B1350 is output | B |
| B | .gif) | GO TO DTC CHART B1350 |
|
.gif)
| 2. | PERFORM ACTIVE TEST USING GTS |
(a) Connect the GTS to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the GTS on.
(d) Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.
(e) Perform the Active Test according to the display on the GTS.
Body Electrical > Vehicle Proximity Notification System > Active Test| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Proximity Sound (Vehicle Stationary) | 0 km/h (0 mph) vehicle proximity warning sound | OFF or ON | - |
| Tester Display |
|---|
| Proximity Sound (Vehicle Stationary) |
| Result | Proceed to |
|---|---|
| The warning sound is produced | A |
| The warning sound is not produced | B |
| A | | REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER |
|
| 3. | CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND) |
(a) Disconnect the A80 vehicle approaching speaker controller connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A80-1 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A80-6 (GND) - Body ground | Always | Below 1 Ω |
| OK | | REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
Vehicle Approaching Speaker
ComponentsCOMPONENTS ILLUSTRATION *1 RADIATOR SUPPORT OPENING COVER *2 VEHICLE APPROACHING SPEAKER ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque - - RemovalREMOVAL PROCEDU
Components
COMPONENTS ILLUSTRATION *1 DECK FLOOR BOX LH *2 NO. 3 DECK BOARD SUB-ASSEMBLY *3 REAR DECK FLOOR BOX *4 NEGATIVE AUXILIARY BATTERY TERMINAL N*m (kgf*cm, ft.*lbf): Specified
SEE MORE:
Dtc Check / Clear
DTC CHECK / CLEAR CHECK FOR DTC (a) Turn the power switch off. (b) Connect the Techstream to the DLC3. (c) Turn the power switch on (IG). (d) Turn the Techstream on. (e) Enter the following menus: Body Electrical / Back Door / Trouble Codes. (f) Check for DTCs. Click here Body Electrical > Back
Removal
REMOVAL PROCEDURE 1. REMOVE MULTI-DISPLAY ASSEMBLY Click here 2. REMOVE DOOR SCUFF PLATE ASSEMBLY LH Click here 3. REMOVE COWL SIDE TRIM BOARD LH Click here 4. REMOVE REAR CONSOLE ARMREST ASSEMBLY Click here 5. REMOVE UPPER REAR CONSOLE PANEL Click here 6. REMOVE UPPER NO. 1 CONSOLE P
