Lexus NX: Touch Pad Memory Module Malfunction (B155B)
DESCRIPTION
This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad memory module malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B155B | Touch Pad Memory Module Malfunction | Internal memory module malfunction | Remote operation controller assembly (remote touch) |
PROCEDURE
| 1. | CHECK DTC |
(a) Clear the DTCs.
Click here .gif)
(b) Recheck for DTCs and check that no DTCs are output.
Click here
OK:
No DTCs are output.
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. | CHECK INFORMATION CODE |
(a) Check that the part number of the remote operation controller assembly (remote touch) is correct.
| Result | Proceed to |
|---|---|
| The part number of the remote operation controller assembly (remote touch) is correct | A |
| The part number of the remote operation controller assembly (remote touch) is incorrect | B |
| B | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
|
| 3. | REMOTE TOUCH SELF CHECK (CHECK TOUCH SCREEN OPERATION POSITION RECOGNITION CONDITION) |
(a) Enter self-diagnostic mode.
Click here
(b) Operate the remote touch screen laterally and check that the touch screen generates vibration feedback.
NOTICE:
Since the remote touch screen may recognize a pinch in/out or flick operation if operated with 2 fingers, always use 1 finger to operate the remote touch in self-diagnostic mode.
HINT:
When operating at an excessively low temperature, vibration feedback may be difficult to feel.
| Result | Proceed to |
|---|---|
| Vibration feedback is generated according to touch panel operation | A |
| The switch illumination changes but vibration feedback is not generated in accordance to touch screen operation | B |
| B | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
|
| 4. | CHECK DTC |
(a) Clear the DTCs.
Click here
(b) Turn the power switch off.
(c) Turn the power switch on (ACC) and wait for 5 seconds.
(d) Recheck for DTCs and check that no DTCs are output.
Click here
OK:
No DTCs are output.
| OK | | USE SIMULATION METHOD TO CHECK |
| NG | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
READ NEXT:
GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) (B1574)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B1574 GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) GVIF disconnected (from p
GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) (B1575)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B1575 GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) GVIF disconnected (from radio receiver
Voice Recognition Microphone Disconnected (B1579)
DESCRIPTION The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines. This DTC is stored when a microphone conne
SEE MORE:
Passenger Side Buckle Switch Circuit Malfunction (B1771)
DESCRIPTION The front passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly RH. DTC B1771 is stored when a malfunction is detected in the front passenger side buckle switch circuit. Troubleshoot DTC B1771 first when DTCs B1771 and B1795 are ou
Throttle Actuator Control Motor Circuit Low (P2102,P2103)
DESCRIPTION The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback
