Lexus NX: Touch Pad Sensor Malfunction (B1559)
DESCRIPTION
This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad sensor malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1559 | Touch Pad Sensor Malfunction | Internal touch pad sensor malfunction | Remote operation controller assembly (remote touch) |
PROCEDURE
| 1. | CHECK DTC |
(a) Clear the DTCs.
Click here .gif)
(b) Recheck for DTCs and check that no DTCs are output.
Click here
OK:
No DTCs are output.
HINT:
-
If DTC B155B is output, perform troubleshooting for DTC B155B first.
Click here
- Touch pad touch detection is performed using the electrostatic sensor and G sensor. However, there is no effect on the basic functions of the touch pad when the G sensor is not operating. Therefore, a counter is used to prevent DTCs from being output immediately (in order to reduce excessive DTC output). Therefore, when DTCs are not output, it is necessary to turn the power switch from on (ACC) to off and check for DTCs again.
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. | REMOTE TOUCH SELF CHECK (CHECK TOUCH SCREEN OPERATION POSITION RECOGNITION CONDITION) |
(a) Enter self-diagnostic mode.
Click here
| (b) Operate the remote touch screen diagonally from the upper left to the lower right and check that the brightness of the switch illumination changes. NOTICE: Since the remote touch screen may recognize a pinch in/out operation if operated with 2 fingers, always use 1 finger to operate the remote touch in self-diagnostic mode. OK: Brightness changes according to touch screen operation.
|
|
.png)
| B | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
|
| 3. | CHECK DTC |
(a) Clear the DTCs.
Click here
(b) Turn the power switch off.
(c) Turn the power switch on (ACC) and wait for 40 seconds.
(d) Recheck for DTCs and check that no DTCs are output.
Click here
OK:
No DTCs are output.
HINT:
Touch pad touch detection is performed using the electrostatic sensor and G sensor. However, there is no effect on the basic functions of the touch pad when the G sensor is not operating. Therefore, a counter is used to prevent DTCs from being output immediately (in order to reduce excessive DTC output). Therefore, when DTCs are not output, it is necessary to turn the power switch from on (ACC) to off and check for DTCs again.
| OK | | USE SIMULATION METHOD TO CHECK |
| NG | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
READ NEXT:
Touch Pad Vibration Driver Malfunction (B155A)
DESCRIPTION This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad vibration driver malfunction.
Touch Pad Memory Module Malfunction (B155B)
DESCRIPTION This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad memory module malfunction.
GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) (B1574)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B1574 GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) GVIF disconnected (from p
SEE MORE:
On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT RESERVOIR CAP (a) Measure the valve opening pressure. *a O-Ring *b Rubber Packing (1) If there are water stains or foreign matter on the O-ring, clean it with water and finger scouring. (2) Check that the O-ring is not deformed, cracked or sw
Removal
REMOVAL PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precoution thoroughly before serving. Click here NOTICE: After turning the power switch off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal. Click here 2. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY C
