Lexus NX: Touch Pad Vibration Driver Malfunction (B155A)
DESCRIPTION
This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad vibration driver malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B155A | Touch Pad Vibration Driver Malfunction | Internal vibration driver malfunction | Remote operation controller assembly (remote touch) |
PROCEDURE
| 1. | CHECK DTC |
(a) Clear the DTCs.
Click here .gif)
(b) Recheck for DTCs and check that no DTCs are output.
Click here
OK:
No DTCs are output.
HINT:
If DTC B155B, B1559 is output, perform troubleshooting for DTC B155B, B1559 first.
B155B: Click here
B1559: Click here
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. | REMOTE TOUCH SELF CHECK (CHECK TOUCH SCREEN OPERATION POSITION RECOGNITION CONDITION) |
(a) Enter self-diagnostic mode.
Click here
(b) Operate the remote touch screen laterally and check that the touch screen generates vibration feedback.
NOTICE:
Since the remote touch screen may recognize a pinch in/out or flick operation if operated with 2 fingers, always use 1 finger to operate the remote touch in self-diagnostic mode.
HINT:
When operating at an excessively low temperature, vibration feedback may be difficult to feel.
| Result | Proceed to |
|---|---|
| Vibration feedback is generated according to touch panel operation | A |
| The switch illumination changes but vibration feedback is not generated in accordance to touch screen operation | B |
| B | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
|
| 3. | CLEAR DTC |
(a) Clear the DTCs.
Click here
|
| 4. | CHECK FEEDBACK VIBRATION |
(a) Turn the power switch on (ACC), swipe the MENU screen to move the cursor and pull it over the button with the vibration feedback.
HINT:
Using the multi-display assembly customize setting screen, check that the remote touch screen vibration feedback reaction force setting is not set to "NO VIBRATION".
Click here
|
| 5. | CHECK DTC |
(a) Recheck for DTCs and check if the same DTC is output again.
Click here
OK:
No DTCs are output.
| OK | | USE SIMULATION METHOD TO CHECK |
| NG | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
READ NEXT:
Touch Pad Memory Module Malfunction (B155B)
DESCRIPTION This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad memory module malfunction.
GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) (B1574)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B1574 GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) GVIF disconnected (from p
GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) (B1575)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B1575 GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) GVIF disconnected (from radio receiver
SEE MORE:
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Smart Access / Trouble Codes. Body Electrical > Smart Access > Trouble Codes (e) Check the details of the DTCs. Cl
Dtc Check / Clear
DTC CHECK / CLEAR DTC CHECK (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes. Body Electrical > Vehicle Proximity Notification System > T
