Lexus NX: Components
COMPONENTS
ILLUSTRATION
| *1 | DECK FLOOR BOX LH | *2 | NO. 3 DECK BOARD SUB-ASSEMBLY |
| *3 | REAR DECK FLOOR BOX | *4 | AUXILIARY BATTERY NEGATIVE TERMINAL |
.png) | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT SEAT ASSEMBLY LH | *2 | FRONT SEAT HEADREST ASSEMBLY |
| *3 | FRONT SEAT INNER TRACK BRACKET COVER LH | *4 | FRONT SEAT OUTER TRACK BRACKET COVER LH |
| *5 | FRONT SEAT REAR INNER TRACK COVER LH | *6 | FRONT SEAT REAR OUTER TRACK COVER LH |
| | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for Driver Side | *B | for Front Passenger Side |
| *1 | FRONT SEAT INNER BELT ASSEMBLY LH | *2 | FRONT SEAT INNER BELT ASSEMBLY RH |
| *3 | SEAT ADJUSTER COVER CAP LH | *4 | FRONT SEAT BELT ANCHOR PLATE |
| | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for Driver Side | - | - |
| *1 | FRONT INNER SEAT CUSHION SHIELD LH | *2 | FRONT LOWER SEAT CUSHION SHIELD |
| *3 | FRONT LUMBAR POWER SEAT SWITCH | *4 | FRONT POWER SEAT SWITCH LH |
| *5 | FRONT SEAT CUSHION SHIELD LH | *6 | POWER SEAT SWITCH KNOB LH |
| *7 | POWER SEAT SWITCH KNOB LH | *8 | SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD LH |
ILLUSTRATION
| *1 | SEAT COVER WIRE | *2 | SEPARATE TYPE FRONT SEAT CUSHION COVER LH |
| *3 | SEPARATE TYPE FRONT SEAT CUSHION PAD LH | *4 | HOG RING |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | FRONT SEAT HEADREST SUPPORT | *2 | SEATBACK FELT |
| *3 | SEPARATE TYPE FRONT SEATBACK COVER WITH PAD | *4 | HOG RING |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | SEAT COVER WIRE | *2 | SEPARATE TYPE FRONT SEATBACK COVER LH |
| *3 | SEPARATE TYPE FRONT SEATBACK PAD LH | *4 | HOG RING |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | w/ Climate Control Seat System | *B | w/o Climate Control Seat System |
| *C | for Driver Side | *D | for Front Passenger Side |
| *1 | FRONT NO. 2 SEAT WIRE LH | *2 | FRONT NO. 2 SEAT WIRE RH |
| *3 | FRONT SEAT AIRBAG ASSEMBLY LH | *4 | SEATBACK CLIMATE CONTROL BLOWER LH |
| *5 | SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for Front Passenger Side | - | - |
| *1 | FRONT NO. 1 SEATBACK HOOK | *2 | FRONT SEATBACK EDGE PROTECTOR |
| *3 | FRONT SEATBACK SPRING SUB-ASSEMBLY RH | *4 | LUMBAR SUPPORT ADJUSTER ASSEMBLY LH |
ILLUSTRATION
| *A | for Driver Side | *B | for Front Passenger Side |
| *C | w/ Climate Control Seat System | *D | w/o Climate Control Seat System |
| *E | w/ Seat Heater System | - | - |
| *1 | FRONT LOWER SEAT CUSHION SHIELD LH | *2 | FRONT LOWER SEAT CUSHION SHIELD RH |
| *3 | FRONT SEAT CUSHION AIRBAG ASSEMBLY RH | *4 | FRONT SEAT CUSHION EDGE PROTECTOR LH |
| *5 | FRONT SEAT CUSHION EDGE PROTECTOR RH | *6 | FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH |
| *7 | FRONT SEAT WIRE LH | *8 | FRONT SEAT WIRE RH |
| *9 | FRONT SEAT WIRE RH | *10 | OCCUPANT DETECTION ECU |
| *11 | SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH | *12 | SEAT CUSHION CLIMATE CONTROL BRACKET LH |
| *13 | SEAT CUSHION CLIMATE CONTROL DUCT LH | *14 | SEAT HEATER CONTROL SUB-ASSEMBLY LH |
| *15 | SEAT POSITION AIRBAG SENSOR | *16 | SEAT SLIDE POSITION SENSOR PROTECTOR |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below i
Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. HINT:
Use the same procedure for the RH and LH sides.
The procedure listed bel
Inspection
INSPECTION PROCEDURE 1. INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH (w/o Memory) (a) Check the operation of the slide motor. (1) Apply auxiliary battery voltage to the slide motor connector, and check
SEE MORE:
Vehicle Approaching Sound ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Vehicle Approaching Sound ECU Communication Stop Mode Any of the following conditions are met:
Communication stop for "Vehicle Proximity Notification System" is indicated on the "Communication Bus Check" screen of the Techstream.
Click
Replacement
REPLACEMENT PROCEDURE 1. REPLACE INTAKE VALVE GUIDE BUSH (a) Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F). (b) Place the cylinder head sub-assembly on wooden blocks. (c) Using SST and a hammer, tap out the intake valve guide bush. SST: 09201-01055 SST: 09950-7
