Lexus NX: Components
COMPONENTS
ILLUSTRATION
.png)
| *1 | DECK FLOOR BOX LH | *2 | NO. 3 DECK BOARD SUB-ASSEMBLY |
| *3 | REAR DECK FLOOR BOX | *4 | NEGATIVE AUXILIARY BATTERY TERMINAL |
.png) | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | PARKING BRAKE ACTUATOR ASSEMBLY LH | *2 | REAR DISC BRAKE CYLINDER ASSEMBLY LH |
| *3 | O-RING | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
.png) | Lithium soap base glycol grease | - | - |
ILLUSTRATION
| *1 | DISC BRAKE CYLINDER MOUNTING LH | *2 | REAR NO. 1 DISC BRAKE ANTI-SQUEAL SHIM |
| *3 | REAR DISC | *4 | REAR DISC BRAKE BUSH DUST BOOT |
| *5 | REAR DISC BRAKE CYLINDER SLIDE BUSH | *6 | REAR DISC BRAKE CYLINDER SLIDE PIN |
| *7 | REAR DISC BRAKE PAD KIT | *8 | REAR NO. 1 DISC BRAKE PAD SUPPORT PLATE |
| *9 | REAR DISC BRAKE REAR CYLINDER SLIDE PIN | *10 | REAR NO. 2 DISC BRAKE ANTI-SQUEAL SHIM |
| *11 | REAR NO. 2 DISC BRAKE PAD SUPPORT PLATE | *12 | PAD WEAR INDICATOR PLATE |
| *13 | REAR DISC BRAKE ANTI-SQUEAL SHIM | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| | Lithium soap base glycol grease | .png) | Disc brake grease |
ILLUSTRATION
| *1 | CYLINDER BOOT | *2 | PISTON SEAL |
| *3 | REAR DISC BRAKE BLEEDER PLUG | *4 | REAR DISC BRAKE BLEEDER PLUG CAP |
| *5 | REAR DISC BRAKE CYLINDER ASSEMBLY LH | *6 | REAR DISC BRAKE PISTON |
| *7 | REAR FLEXIBLE HOSE LH | *8 | UNION BOLT |
| *9 | GASKET | - | - |
| | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| | Lithium soap base glycol grease | - | - |
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
NOTICE:
When the brake pedal is first depressed after repla
Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
PROCEDURE 1. REMOVE CYLINDER BOOT (a) Using a screwdriv
Inspection
INSPECTION PROCEDURE 1. CHECK BRAKE CYLINDER AND PISTON (a) Check the cylinder bore and piston for rust or scoring. If necessary, replace the disc brake cylinder and piston. 2. CHECK PAD LINING THICKN
SEE MORE:
HV Battery High-voltage Line Circuit
DESCRIPTION The cause of the malfunction may be the HV battery high-voltage line circuit. Check the continuity in the high-voltage line from the HV battery to the inverter. Check the connection condition and for an open circuit in the frame wire from the service plug grip and HV battery to the inver
Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE 1. REMOVE FRONT SEAT ASSEMBLY LH Click here 2. REMOVE FRONT SEAT
