Lexus NX: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
*: Use the Techstream.
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. | CUSTOMER PROBLEM ANALYSIS |
|
| 3. | CONNECT TECHSTREAM TO DLC3* |
HINT:
If the display indicates a communication malfunction, inspect the DLC3.
When any CAN communication system DTCs are output, perform troubleshooting on the CAN communication system first.
|
| 4. | CHECK DTC AND FREEZE FRAME DATA* |
(a) Check for DTCs.
Click here .gif)
(b) Check for freeze frame data.
Click here
HINT:
Record or print DTCs and freeze frame data if necessary.
|
| 5. | CLEAR DTC AND FREEZE FRAME DATA* |
(a) Clear the DTCs and freeze frame data.
Click here
|
| 6. | CONDUCT VISUAL INSPECTION |
|
| 7. | SELECT CHECK MODE DIAGNOSIS* |
(a) Switch the ECM from normal mode to check mode.
Powertrain > Engine and ECT > Utility| Tester Display |
|---|
| Check Mode |
HINT:
Refer to Check Mode Procedure.
Click here
|
| 8. | CONFIRM PROBLEM SYMPTOMS |
(a) Confirm problem symptoms.
HINT:
If the engine does not start, first perform the "Check DTC" procedure and "Conduct Basic Inspection" procedure below.
| Result | Proceed to |
|---|---|
| Malfunction does not occur | A |
| Malfunction occurs | B |
| B | .gif) | GO TO STEP 10 |
|
| 9. | SIMULATE SYMPTOMS |
HINT:
Refer to Symptom Simulation.
Click here
|
| 10. | CHECK DTC* |
(a) Check for DTCs.
Powertrain > Engine and ECT > Trouble CodesHINT:
Refer to DTC Check / Clear.
Click here
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
| B | | GO TO STEP 12 |
|
| 11. | REFER TO DTC CHART |
HINT:
Refer to Diagnostic Trouble Code Chart.
Click here
|
| 12. | CONDUCT BASIC INSPECTION |
(a) Conduct basic inspection.
HINT:
Refer to Basic Inspection.
Click here
| Result | Proceed to |
|---|---|
| Malfunctioning parts not confirmed | A |
| Malfunctioning parts confirmed | B |
| B | | GO TO STEP 17 |
|
| 13. | REFER TO PROBLEM SYMPTOMS TABLE |
HINT:
Refer to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Malfunctioning circuit confirmed | A |
| Malfunctioning parts confirmed | B |
| B | | GO TO STEP 17 |
|
| 14. | CHECK ECM POWER SOURCE CIRCUIT |
(a) Check the ECM power source circuit.
HINT:
Refer to ECM Power Source Circuit.
Click here
|
| 15. | CONDUCT CIRCUIT INSPECTION |
| Result | Proceed to |
|---|---|
| Malfunction not confirmed | A |
| Malfunction confirmed | B |
| B | | GO TO STEP 18 |
|
| 16. | CHECK FOR INTERMITTENT PROBLEMS |
(a) Check for intermittent problems.
HINT:
Refer to Check for Intermittent Problems.
Click here
|
| 17. | CONDUCT PARTS INSPECTION |
|
| 18. | IDENTIFY PROBLEM |
|
| 19. | ADJUST AND/OR REPAIR |
|
| 20. | CONDUCT CONFIRMATION TEST |
| NEXT | | END |
READ NEXT:
Check For Intermittent Problems
CHECK FOR INTERMITTENT PROBLEMS HINT: Inspect the vehicle ECM using check mode. Intermittent problems are easier to detect with the Techstream when the ECM is in check mode. In check mode, the ECM use
Basic Inspection
CAUTION / NOTICE / HINT When a malfunction is not confirmed by the DTC check, troubleshooting should be carried out for all circuits considered to be possible causes of the problem. In many cases, by
Registration
REGISTRATION CAUTION / NOTICE / HINT NOTICE: The Vehicle Identification Number (VIN) must be input into a replacement ECM. HINT: The VIN is a 17-digit alphanumeric vehicle identification number. The T
SEE MORE:
Side Camera Current Malfunction (C1684)
DESCRIPTION This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU. DTC No. Detection Item DTC Detection Condition Tro
Precaution
PRECAUTION POINTS TO NOTE WHEN SERVICING (a) Pay attention to the following points when servicing. (1) When disconnecting the cable from the negative (-) auxiliary battery terminal, "!" mark may appear on the multi-display assembly. In this case, restore the steering angle neutral point. Click here
