Lexus NX manuals

Lexus NX: Operation Check

Lexus NX Service Manual / Audio & Visual & Telematics / Telematics / Telematics System / Operation Check

OPERATION CHECK

HINT:

  • This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal strength is very weak.
  • This function is used to display operation history information and the time at which it was stored in the DCM (telematics transceiver).

CHECK DCM OPERATION HISTORY

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Telematics / Utility / DCM Operation History.

Body Electrical > Telematics > Utility

Tester Display

DCM Operation History

(e) Choose "Items" on the DCM Operation History Menu.

HINT:

  • When "Operation Code" is recorded, DCM Operation History is displayed on the Techstream.
  • The displayed "Function" differs depending on the selected "Items".

(f) Refer to the following chart and check the system operation status displayed on the Techstream. (The following chart is an example of the system operation status.)

System Operation Status Example

Occurrence Time*1

Operation Code*2

Function*3

Content*4

Roaming*5

Voice Call*6

Service Area*7

Electric Level*8

2017/12/31 12:40:50

0101

GNSS (Satellite)

Unreceived GNSS (Satellite) signal

ON

With

Out of Service

Level 0
Tester Display Description

Tester Display

Description

Range

*1

Occurrence time

Indicates date of the DCM (telematics transceiver) operation.

-

*2

Operation Code

Indicates the Operation Code.

-

*3

Function

Items

Indicates the function name.

-

Common
  • GNSS (Satellite)
  • Collision Detection
  • Network Power Supply Control
  • SMS
  • Telematics PF
  • Failure Due to Conflict
  • Activate Function

Remote Diagnostics
  • Remote Warning
  • Remote DTC / FFD
  • Remote Monitoring
  • Remote Vehicle History
  • Remote DTC / FFD on IP
  • Remote Monitoring on IP

Center Request

Center Request Command

Remote Service
  • Maintenance Assistance
  • Remote Diagnostics Recorder
  • Remote Confirmation
  • Under Repair Rejection
  • Last File

Remote Control
  • Remote Control
  • Remote Hazard
  • Remote Door Lock
  • Remote Power Window
  • Pre Air-Conditioning

Security
  • Alarm Notification
  • Remote Immobilizer
  • Stolen Vehicle Tracking
  • Remote Vehicle Tracking

Operation Monitor

Operation Monitoring

Network
  • Air Data Feed
  • APN Selection
  • TSC Client Authentication
  • Simple HTTP Proxy 1
  • Simple HTTP Proxy 2
  • Simple HTTP Proxy 3
  • Simple HTTP Proxy 4
  • Simple HTTP Proxy 5
  • Simple HTTP Proxy 6
  • Simple HTTP Proxy 7
  • Simple HTTP Proxy 8

Vehicle Information
  • Vehicle Info. CAN
  • Vehicle Info. Ethernet

*4

Content

Indicates the content.

-

*5

Roaming

Indicates whether roaming was used for the communication network.

ON or OFF

*6

Voice Call

Indicates whether there was a voice call.

With or Without

*7

Service Area

Indicates whether the vehicle was in the service area.

Out of Service, Within Range, OFF the Air or Start up (LTE)

*8

Electric Level

Indicates the strength of the cellular signal received by the vehicle.

Level 0, Level 1, Level2, Level3, Level 4, Level 5

READ NEXT:

 Utility

UTILITY CANCEL COMMUNICATION FUNCTION PAUSING HINT: This function is used to cancel communication function pausing mode (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) T

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of

 Terminals Of Ecu

TERMINALS OF ECU DCM (TELEMATICS TRANSCEIVER) Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I183-1 (+B) - I183-20 (E) Y - W-B Power source (

SEE MORE:

 Brake Warning Light does not Come ON

DESCRIPTION The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication. CAUTION / NOTICE / HINT NOTICE: When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibrati

 Reassembly

REASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. INSTALL NO. 2 ROOF CARRIER PROTECTOR (a) Clean the roof rack surface. (1) Remove the double-sided tape from the roof rack. (2) Wipe off any tap

© 2016-2025 Copyright www.lexunx.com