Lexus NX: Position Initialization Incomplete (B2343)
DESCRIPTION
This DTC is stored when the sliding roof drive gear sub-assembly (sliding roof ECU) has not been initialized.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2343 | Position Initialization Incomplete | Sliding roof drive gear sub-assembly (sliding roof ECU) has not been initialized. | Sliding roof drive gear sub-assembly (sliding roof ECU) |
WIRING DIAGRAM
.png)
CAUTION / NOTICE / HINT
NOTICE:
-
If the sliding roof drive gear sub-assembly (sliding roof ECU) is replaced, the sliding roof drive gear sub-assembly (sliding roof ECU) must be initialized.
Click here
.gif)
-
The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.
Click here
HINT:
When DTC B2342 and B2343 are output simultaneously, perform troubleshooting for DTC B2342 first.
PROCEDURE
| 1. | INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
(a) Check that the sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.
Click here
OK:
Sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.
| NG | .gif) | GO TO STEP 4 |
|
.gif)
| 2. | CHECK SLIDING ROOF OPERATION |
(a) Check the sliding roof auto operation.
Click here
OK:
Auto operation operates normally.
| NG | | REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
|
| 3. | CHECK DTC OUTPUT |
(a) Clear the DTCs.
Click here
(b) Check for DTCs.
Click here
OK:
DTC B2343 is not output.
| OK | | END (MALFUNCTION DUE TO INITIALIZATION FAILURE) |
| NG | | REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
| 4. | PERFORM ACTIVE TEST USING TECHSTREAM (Slide Roof) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Slide Roof / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Sliding Roof > Active Test| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof motor | OFF / Opn/Dwn / Clos/Up | - |
| Tester Display |
|---|
| Slide Roof |
OK:
Slide roof is operated using Techstream.
| NG | | REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
|
| 5. | READ VALUE USING TECHSTREAM (Open Switch, Close Switch, Up Switch, Down Switch) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Roof > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | OPEN switch signal | OFF or ON | OFF: OPEN switch not pressed ON: OPEN switch pressed | - |
| Close Switch | CLOSE switch signal | OFF or ON | OFF: CLOSE switch not pressed ON: CLOSE switch pressed | - |
| Up Switch | UP switch signal | OFF or ON | OFF: UP switch not pressed ON: UP switch pressed | - |
| Down Switch | DOWN switch signal | OFF or ON | OFF: DOWN switch not pressed ON: DOWN switch pressed | - |
| Tester Display |
|---|
| Open Switch |
| Close Switch |
| Up Switch |
| Down Switch |
OK:
The Techstream display changes according to switch operation as shown in the table.
| OK | | REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
|
| 6. | INSPECT MAP LIGHT ASSEMBLY |
(a) Remove the map light assembly (slide roof switch).
Click here
(b) Inspect the map light assembly (slide roof switch).
Click here
| NG | | REPLACE MAP LIGHT ASSEMBLY |
|
| 7. | CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - MAP LIGHT ASSEMBLY AND BODY GROUND) |
(a) Disconnect the T9 sliding roof drive gear sub-assembly connector.
(b) Disconnect the T6 map light assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T9-4 (UP) - T6-23 (UP) | Always | Below 1 Ω |
| T9-4 (UP) or T6-23 (UP) - Body ground | Always | 10 kΩ or higher |
| T9-5 (CLS) - T6-12 (CLS) | Always | Below 1 Ω |
| T9-5 (CLS) or T6-12 (CLS) - Body ground | Always | 10 kΩ or higher |
| T9-6 (DWN) - T6-24 (DOWN) | Always | Below 1 Ω |
| T9-6 (DWN) or T6-24 (DOWN) - Body ground | Always | 10 kΩ or higher |
| T9-7 (OPN) - T6-11 (OPN) | Always | Below 1 Ω |
| T9-7 (OPN) or T6-11 (OPN) - Body ground | Always | 10 kΩ or higher |
| T9-12 (E) - Body ground | Always | Below 1 Ω |
| T6-19 (GND) - Body ground | Always | Below 1 Ω |
| OK | | REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
Remote Control System does not Operate
DESCRIPTION The main body ECU (multiplex network body ECU) receives remote control signals from the driver door key cylinder or wireless transmitter. Then, the main body ECU (multiplex network body EC
Key-off Operation Function Operates even if Operating Conditions are not Satisfied
DESCRIPTION According to the map light assembly (slide roof switch) operation, the sliding roof drive gear sub-assembly (sliding roof ECU) operates its built-in motor. Using the map light assembly (sl
Sliding Roof does not Move by Operating Sliding Roof Control Switch
DESCRIPTION The sliding roof drive gear sub-assembly (sliding roof ECU) receives each signal when the map light assembly (slide roof switch) is operated and drives its built-in motor. WIRING DIAGRAM
SEE MORE:
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT:
Before troubleshooting the front camera system, first refer to How to Proceed with Troubleshooting for the pre-collision system.
Click here
If a message is displayed on the multi-information display, refer to How to Proceed with Troubleshooting for the pre-collis
Buzzer Circuit Short to Ground or Open (C1A4A14)
DESCRIPTION If the forward recognition camera detects an open or short to ground in the buzzer circuit, it will store DTC C1A4A14. DTC No. Detection Item DTC Detection Condition Trouble Area C1A4A14 Buzzer Circuit Short to Ground or Open The forward recognition camera detects an ope
