Lexus NX: Remote Control System does not Operate
DESCRIPTION
The main body ECU (multiplex network body ECU) receives remote control signals from the driver door key cylinder or wireless transmitter. Then, the main body ECU (multiplex network body ECU) activates the power window motor and sends the remote control signals to the sliding roof drive gear sub-assembly (sliding roof ECU) via LIN communication. The sliding roof drive gear sub-assembly (sliding roof ECU) receives those signals and activates the sliding roof motor.
CAUTION / NOTICE / HINT
NOTICE:
-
The sliding roof key-linked function and sliding roof wireless transmitter-linked function can be customized. Make sure that both functions are ON.
Click here
.gif)
-
If the sliding roof drive gear sub-assembly (sliding roof ECU) is replaced, the sliding roof drive gear sub-assembly (sliding roof ECU) must be initialized.
Click here
-
The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to How to Proceed with Troubleshooting.
Click here
-
If a sliding roof drive gear sub-assembly (sliding roof ECU) DTC is output, first perform troubleshooting for the sliding roof drive gear sub-assembly (sliding roof ECU) DTC.
Click here
-
If the main body ECU (multiplex network body ECU) is replaced, refer to the Smart Access System with Push-button Start (for Entry Function).
Click here
PROCEDURE
| 1. | CHECK REMOTE CONTROL FUNCTION |
(a) Check the key-linked and wireless transmitter-linked function.
Click here
| Result | Proceed to |
|---|---|
| Both the power windows and sliding roof operate by the key-linked and wireless transmitter-linked function. | A |
| The sliding roof does not operate by the key-linked or wireless transmitter-linked function, but all the power windows operate. | B |
| Both the power windows and roof glass do not operate by the key-linked or wireless transmitter-linked function. | C |
| A | .gif) | USE SIMULATION METHOD TO CHECK |
| C | | GO TO POWER WINDOW CONTROL SYSTEM |
|
.gif)
| 2. | CHECK SLIDING ROOF OPERATION |
(a) Check the sliding roof operation.
Click here
OK:
Sliding roof operates normally.
| NG | | GO TO OTHER PROBLEM (Sliding Roof does not Move by Operating Sliding Roof Control Switch) |
|
| 3. | REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
(a) Replace the sliding roof ECU (sliding roof drive gear sub-assembly).
Click here
|
| 4. | INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
(a) Initialize the sliding roof drive gear sub-assembly.
Click here
|
| 5. | CHECK REMOTE CONTROL FUNCTION |
(a) Check the key-linked and wireless transmitter-linked function.
Click here
OK:
The key-linked and wireless transmitter-linked* function operates normally.
| OK | | END (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY WAS DEFECTIVE) |
| NG | | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
READ NEXT:
Key-off Operation Function Operates even if Operating Conditions are not Satisfied
DESCRIPTION According to the map light assembly (slide roof switch) operation, the sliding roof drive gear sub-assembly (sliding roof ECU) operates its built-in motor. Using the map light assembly (sl
Sliding Roof does not Move by Operating Sliding Roof Control Switch
DESCRIPTION The sliding roof drive gear sub-assembly (sliding roof ECU) receives each signal when the map light assembly (slide roof switch) is operated and drives its built-in motor. WIRING DIAGRAM
SEE MORE:
Engine Coolant Temperature Receiver Gauge Malfunction
DESCRIPTION In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM via the CAN communication system. The combination meter assembly displays the engine coolant temperature that is calculated based on the data received from the ECM. WIRING DIAGRAM CA
Disposal
DISPOSAL CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE 1. DISPOSE OF FRONT SHOCK ABSORBER ASSEMBLY LH (a) Position the front shock absorber assembly so that it is level with the piston rod fully exten
