Lexus NX: Components
COMPONENTS
ILLUSTRATION
| *A | for RH Side | - | - |
| *1 | REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY | *2 | REAR SEAT CUSHION MOULDING RH |
| *3 | REAR SEAT CUSHION MOULDING RH | *4 | REAR SEAT HEADREST ASSEMBLY |
| *5 | REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH | *6 | REAR SEATBACK BOARD CARPET ASSEMBLY RH |
| *7 | REAR SEATBACK COVER | *8 | SEPARATE TYPE REAR SEATBACK COVER WITH PAD |
.png) | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LH Side | - | - |
| *1 | CENTER ARMREST HINGE COVER | *2 | CENTER SEAT HINGE COVER |
| *3 | NO. 1 SEAT ARMREST ASSEMBLY | *4 | NO. 1 SEATBACK COVER |
| *5 | REAR CENTER SEAT HEADREST ASSEMBLY | *6 | REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
| *7 | REAR SEAT ARMREST HOLE COVER | *8 | REAR SEAT CENTER ARMREST ASSEMBLY |
| *9 | REAR SEAT CUSHION MOULDING LH | *10 | REAR SEAT CUSHION MOULDING LH |
| *11 | REAR SEAT HEADREST ASSEMBLY | *12 | REAR SEAT INNER BELT ASSEMBLY LH |
| *13 | REAR SEATBACK BOARD CARPET ASSEMBLY LH | *14 | REAR SEATBACK COVER |
| *15 | SEPARATE TYPE REAR SEATBACK COVER WITH PAD | *16 | REAR SEATBACK PROTECTOR SHAFT BUSH |
| | N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for RH Side | *B | for LH Side |
| *1 | SEPARATE TYPE REAR SEATBACK COVER LH (REAR SEATBACK HEATER ASSEMBLY LH) | *2 | SEPARATE TYPE REAR SEATBACK COVER RH (REAR SEATBACK HEATER ASSEMBLY RH) |
| *3 | SEPARATE TYPE REAR SEATBACK PAD LH | *4 | SEPARATE TYPE REAR SEATBACK PAD RH |
| *5 | HOG RING | - | - |
| ● | Non-reusable part | - | - |
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. REMOVE REAR SEAT ASSEMBLY Click here 2. REMOVE REAR SEATBACK COVER Click
Inspection
INSPECTION PROCEDURE 1. INSPECT SEPARATE TYPE REAR SEATBACK COVER RH (REAR SEATBACK HEATER ASSEMBLY RH) (for RH Side) (a) Check the separate type rear seatback cover RH (rear seatback heater assemb
Installation
INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (REAR SEATBACK HEATER AS
SEE MORE:
Reassembly
REASSEMBLY PROCEDURE 1. INSTALL NO. 2 MOULDING TAPE HINT:
When installing the No. 2 moulding tape, heat the front bumper cover and No. 2 moulding tape using a heat light.
Use the same procedure described for the other side.
Standard: Item Temperature Front Bumper Cover 20 to 30°
Steering Wheel does not Heat Up When Heated Steering Wheel Switch is Pressed
DESCRIPTION Click here WIRING DIAGRAM Click here CAUTION / NOTICE / HINT HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
The steering wheel heater unit is built into the steering wheel assembly which cannot be disassembled. T
