Lexus NX: Installation
INSTALLATION
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (REAR SEATBACK HEATER ASSEMBLY LH) (for LH Side)
HINT:
-
When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.
Click here
.gif)
-
Align the seam allowance in a single direction as shown in the illustration.
.png)
| (a) Using hog ring pliers, install the separate type rear seatback cover LH (rear seatback heater assembly LH) to the separate type rear seatback pad LH with 12 new hog rings in the order indicated in the illustration. NOTICE:
|
|
.png)
2. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)
Click here
3. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY (for LH Side)
Click here
4. INSTALL REAR SEAT CUSHION MOULDING LH (for LH Side)
Click here
5. INSTALL REAR SEAT CUSHION MOULDING LH (for LH Side)
Click here
6. INSTALL NO. 1 SEATBACK COVER (for LH Side)
Click here
7. INSTALL CENTER ARMREST HINGE COVER (for LH Side)
Click here
8. INSTALL CENTER SEAT HINGE COVER (for LH Side)
Click here
9. INSTALL NO. 1 SEAT ARMREST ASSEMBLY (for LH Side)
Click here
10. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (for LH Side)
Click here
11. INSTALL REAR SEAT ARMREST HOLE COVER (for LH Side)
Click here
12. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH (for LH Side)
Click here
13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (for LH Side)
Click here
14. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)
Click here
15. INSTALL REAR SEAT INNER BELT ASSEMBLY LH (for LH Side)
Click here
16. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH (REAR SEATBACK HEATER ASSEMBLY RH) (for RH Side)
HINT:
-
When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.
Click here
-
Align the seam allowance in a single direction as shown in the illustration.
.png)
| (a) Using hog ring pliers, install the separate type rear seatback cover RH (rear seatback heater assembly RH) to the separate type rear seatback pad RH with 12 new hog rings in the order indicated in the illustration. NOTICE:
|
|
.png)
17. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)
Click here
18. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY (for RH Side)
Click here
19. INSTALL REAR SEAT CUSHION MOULDING RH (for RH Side)
Click here
20. INSTALL REAR SEAT CUSHION MOULDING RH (for RH Side)
Click here
21. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH (for RH Side)
Click here
22. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)
Click here
23. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (for RH Side)
Click here
24. INSTALL REAR SEATBACK COVER
Click here
25. INSTALL REAR SEAT ASSEMBLY
Click here
26. INSPECT SEAT HEATER SYSTEM (for Rear Seat)
Click here
READ NEXT:
Components
COMPONENTS ILLUSTRATION *A for RH Side - - *1 REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY *2 REAR SEAT CUSHION MOULDING RH *3 REAR SEAT CUSHION MOULDING RH *4 REAR SEAT HEA
Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. REMOVE REAR SEAT ASSEMBLY Click here 2. REMOVE REAR SEATBACK COVER Click
SEE MORE:
Operation Check
OPERATION CHECK HINT:
This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal strength is very weak.
Thi
Components
COMPONENTS ILLUSTRATION *1 COMBINATION SWITCH ASSEMBLY *2 CONSOLE ARMREST ASSEMBLY *3 INSTRUMENT SIDE PANEL LH *4 LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL *5 NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY *6 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY *7 NO.
