Lexus NX: Height Control Sensor Data Out of Range When Initializing (B2452)
DESCRIPTION
The headlight ECU sub-assembly LH stores this DTC if the value from the rear height control sensor sub-assembly LH is out of range when performing initialization of the headlight ECU sub-assembly LH, such as when the vehicle is not level or jacked up.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2452 | Height Control Sensor Data Out of Range When Initializing |
|
|
WIRING DIAGRAM
.png)
CAUTION / NOTICE / HINT
NOTICE:
-
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click here
.gif)
-
After the rear height control sensor sub-assembly LH is replaced or removed and installed, initialization is necessary.
Click here
PROCEDURE
| 1. | INITIALIZATION HEADLIGHT ECU SUB-ASSEMBLY LH |
(a) Perform initialization of the headlight ECU sub-assembly LH.
Click here
|
.gif)
| 2. | CHECK FOR DTC |
(a) Clear the DTCs.
Click here
(b) Turn the power switch on (IG).
(c) Check for DTCs.
Click here
OK:
DTC B2452 is not output.
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
| 3. | CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH |
(a) Check the rear height control sensor sub-assembly LH installation condition.
OK:
Rear height control sensor sub-assembly LH installation condition is normal.
| NG | | INSTALL PARTS CORRECTLY |
|
| 4. | INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH |
(a) Remove the rear height control sensor sub-assembly LH.
Click here
(b) Inspect the rear height control sensor sub-assembly LH.
Click here
| NG | | REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH |
|
| 5. | CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH) |
(a) Disconnect the A19 headlight ECU sub-assembly LH connector.
(b) Disconnect the R1 rear height control sensor sub-assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A19-16 (SBR) - R1-3 (SHB) | Always | Below 1 Ω |
| A19-17 (SHRL) - R1-2 (SHRR) | Always | Below 1 Ω |
| A19-15 (SGR) - R1-1 (SHG) | Always | Below 1 Ω |
| A19-16 (SBR) or R1-3 (SHB) - Body ground | Always | 10 kΩ or higher |
| A19-17 (SHRL) or R1-2 (SHRR) - Body ground | Always | 10 kΩ or higher |
| A19-15 (SGR) or R1-1 (SHG) - Body ground | Always | 10 kΩ or higher |
| OK | | REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
Automatic High Beam Main Switch
InspectionINSPECTION PROCEDURE 1. INSPECT COMBINATION SWITCH ASSEMBLY (AUTOMATIC HIGH BEAM MAIN SWITCH) (a) Remove the combination switch assembly. Click here (b) Inspect the automatic high beam ma
Precaution
PRECAUTION HANDLING PRECAUTIONS FOR FORWARD RECOGNITION CAMERA (a) The automatic high beam system uses the forward recognition camera. For precautions related to the forward recognition camera, refer
SEE MORE:
On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to follow the correct removal and installation procedures of the front seat airbag assemblies. PROCEDURE 1. INSPECT FRONT SEAT AIRBAG ASSEMBLY (for Vehicle not Involved in Collision) (a) Perform a diagnostic system check. Click here (
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE POWER BACK DOOR SYSTEM HINT: The following items can be customized. NOTICE:
When the customer requests a change in a function, first make sure that the function can be customized.
Record the current settings before customizing.
(a) Customizing with the Techstre
