Lexus NX manuals

Lexus NX: Inspection

Lexus NX Service Manual / Vehicle Interior / Seat / Rear Seat Cushion Heater(for Power Seat) / Inspection

INSPECTION

PROCEDURE

1. INSPECT BENCH TYPE REAR SEAT CUSHION COVER (REAR SEAT CUSHION HEATER ASSEMBLY RH)

(a) Check the bench type rear seat cushion cover (rear seat cushion heater assembly RH).

NOTICE:

Disconnect the connector B from the rear seat cushion heater assembly LH before checking it.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A-1 - B-1

Always (23°C)

Below 1 Ω

A-1 - B-2

73.9 to 90.4 Ω

A-1 - B-3

A-1 - A-4

3.34 to 4.08 Ω

A-1 - A-5

A-1 - A-6

Below 1 Ω

A-2 - A-3

7.52 to 9.19 kΩ

A-4 - B-1

3.34 to 4.08 Ω

A-4 - B-2

77.3 to 94.4 Ω

A-4 - B-3

A-4 - A-5

Below 1 Ω

A-4 - A-6

3.34 to 4.08 Ω

A-5 - B-1

A-5 - B-2

77.3 to 94.4 Ω

A-5 - B-3

A-5 - A-6

3.34 to 4.08 Ω

A-6 - B-1

Below 1 Ω

A-6 - B-2

73.9 to 90.4 Ω

A-6 - B-3

B-1 - B-2

B-1 - B-3

B-2 - B-3

Below 1 Ω

If the result is not as specified, replace the bench type rear seat cushion cover (rear seat cushion heater assembly RH).

*a

Connector A

*b

Connector B

*c

Component without harness connected

(Bench Type Rear Seat Cushion Cover (Rear Seat Cushion Heater Assembly RH))

2. INSPECT BENCH TYPE REAR SEAT CUSHION COVER (REAR SEAT CUSHION HEATER ASSEMBLY LH)

(a) Check the bench type rear seat cushion cover (rear seat cushion heater assembly LH).

NOTICE:

Disconnect the connector B from the rear seat cushion heater assembly RH before checking it.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A-1 - B-1

Always (23°C)

Below 1 Ω

A-1 - B-2

3.34 to 4.08 Ω

A-1 - A-4

A-2 - A-3

7.52 to 9.19 kΩ

A-4 - B-1

3.34 to 4.08 Ω

A-4 - B-2

Below 1 Ω

A-5 - B-3

B-1 - B-2

3.34 to 4.08 Ω

If the result is not as specified, replace the bench type rear seat cushion cover (rear seat cushion heater assembly LH).

*a

Connector A

*b

Connector B

*c

Component without harness connected

(Bench Type Rear Seat Cushion Cover (Rear Seat Cushion Heater Assembly LH))

READ NEXT:

 Installation

INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. INSTALL BENCH TYPE REAR SEAT CUSHION COVER (REAR SEAT CUSHION HEATER)

 Rear Seatback Heater(for Manual Seat)

 Components

COMPONENTS ILLUSTRATION *A for RH Side - - *1 REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY *2 REAR SEAT CUSHION MOULDING RH *3 REAR SEAT CUSHION MOULDING RH *4 REAR SEAT HEA

SEE MORE:

 Check Bus 2 Lines for Short Circuit

DESCRIPTION There may be a short circuit between the CAN main bus wire and/or CAN branch wire when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω. Symptom Trouble Area *1: w/ Headup Display *2: w/ ASC System *3: for T

 No Sound can be Heard from Speakers

PROCEDURE 1. CHECK AUDIO SETTINGS (a) In sound output setting mode, set volume, fader and balance to the initial values and check that the sound is normal. OK: Audio system returns to normal. HINT: Sound quality adjustment measures vary according to the type of amplifier. OK END

© 2016-2026 Copyright www.lexunx.com